background image

January 

4, 

2018 

     7082-150C 

       

 

 

 

 

3

MT VERNON E2 INSERT-C

Important Safety Information

NOTE:  Hearth & Home Technologies, manufacturer of this appli

-

ance, reserves the right to alter its products, their specifications 

and/or price without notice.

Improper installation, adjustment, alteration, service or maintenance 

can cause injury or property damage. 

For assistance or additional information, consult a qualified installer, 

service agency or your dealer.

•  Installation and use of any damaged appliance. 

•  Modification of the appliance.
•  Installation  other  than  as  instructed  by  Hearth  &  Home 

Technologies.

•  Installation and/or use of any component part not approved by 

Hearth & Home Technologies.

•  Operating appliance without fully assembling all components.
•  Operating  appliance  without  legs  attached  (if  supplied  with 

appliance).

•  Do NOT Over fire - If appliance or chimney connector glows, 

you are over firing.

Any such action that may cause a fire hazard.

WARNING

Fire Risk.

Hearth & Home Technologies disclaims any 

responsibility for, and the warranty will be 

voided by, the following actions: 

C.  Glass Specifications

This appliance is equipped with 5mm ceramic glass.  

Replace glass only with 5mm ceramic glass.  Please con-

tact your dealer for replacement glass.

Model

Mt. Vernon Insert Pellet Appliance E2

Laboratory

OMNI Test Laboratories, Inc.

Report No.

061-S-84-2

Type

Solid Fuel Room Appliance, Pellet Fuel Burn

-

ing Type

Standard

ASTM E1509-12, ULC-S628-93 and 

(UM) 

84-HUD, Mobile Home Approved.

FCC

Complies with Part 15 of FCC Rules. Opera

-

tion is subject to the following two conditions:  

(1) this device may not cause harmful inter

-

ference, and (2) this device must accept any 

interference received, including interference 

that may cause undesired  operation.

A.  Appliance Certification

NOTICE:  

This installation must conform with local codes. In the 

absence of local codes you must comply with the 

ASTM E1509-

12, ULC S628-93, (UM) 84-HUD and  ULC/ORD-C-1482. 

B.  BTU & Efficiency Specifications

D.  Electrical Rating

115 VAC, 60 Hz, Start 2.9 Amps, Run 2.45 Amps

E.  Mobile Home Approved 

• 

This appliance is approved for mobile home installations when 

not installed in a sleeping room and when an outside combustion 

air inlet is provided.

• 

The structural integrity of the mobile home floor, ceiling, and 

walls must be maintained.  

• 

The appliance must be properly grounded to the frame of the 

mobile home and use only Listed pellet vent Class “L” or “PL” con

-

nector pipe.  

• 

Outside Air  Kit  (OAK-3)  must  be  installed  in  a  mobile  home 

installation.

F. Non-Combustible Materials

Material which will not ignite and burn, composed of any combina

-

tion of the following: 

 - 

Steel 

  - 

Plaster

 

- Brick   

 

- Iron

 - 

Concrete 

 - 

Tile

 - 

Glass 

  - 

Slate

Materials reported as passing 

ASTM E 136, Standard Test 

Method for Behavior of Metals, in a Vertical Tube Furnace of 

750° C. 

G. Combustible Materials

Material made of/or surfaced with any of the following materials: 

 

- Wood   

 

- Compressed Paper

 

- Plant Fibers 

 

- Plastic

 

- Plywood/OSB   

- Sheet Rock (drywall)

Any material that can ignite and burn: flame proofed or not, plas

-

tered or non-plastered.

 

The Quadra-Fire Mt. Vernon E2 Pellet Insert Appliance meets 

the U.S. ENVIRONMENTAL PROTECTION AGENCY 

Certified to 

comply with 2020 particulate emission standards at 0.74 G/HR EPA 

CFR subpart AAA, using ASTM E2779-10, ASTM 2515-11 Method- 
Pellet Appliance sections, CSA B415.1-10

This pellet  appliance 

needs periodic inspection and repair for proper operation. It 

is against federal regulations to operate this pellet appliance 

in a manner inconsistent with the operating instructions in 

the owner’s manual.

Emissions Report Number:

0061PS094E

EPA Certification #:

98-17

EPA Certified Emissions:

0.74 g/hr

*LHV Tested Efficiency:

83.2%

**HHV Tested Efficiency:

77.9%

***EPA BTU Output:

12,682 - 39,428 / HR

****BTU Input:

16,396 - 50,775 / HR

Vent Size: 3 or 4, “L” or “PL”

Hopper Capacity: 52 lbs.

Fuel Wood Pellets

* Weighted average LHV efficiency using data collected during 

EPA emissions test.

**

Weighted average HHV efficiency using data collected during 

EPA emissions test.

***

A range of BTU outputs based on HHV and the burn rates from 

the low and high EPA tests.

****

Based  on  the  maximum  feed  rate  per  hour  multiplied  by 

approximately  8600  BTU’s  which  is  the  average  BTU’s  from  a 

pound of pellets.

Summary of Contents for MTVI-E2-CSB-C





























Reviews: