background image

 12 

 

 

 

 

                       7060-228G 

 

 

 

       November 29, 2016

Explorer III Wood Stove

Chimney Systems

NOTE: I

n Canada when using a factory-built chimney it must 

be safety listed,

 Type UL103 HT (2100

o

F) CLASS “A” 

or 

conforming to 

CAN/ULC-S629M, STANDARD FOR 650

o

FACTORY-BUILT CHIMNEYS.

Floor

Protector

Chimney

Connector

Insulated " T "

Flashing

Listed Termination Cap

Trim Collar on

Inside Wall

Listed Chimney

Storm Collar

Wall Support

Roof Brace (if required)

Thimble

Floor

Protector

Chimney

Connector

Ceiling Support

Listed Chimney

Listed Termination Cap

Storm Collar

Flashing

Figure 12.1 Prefabricated Exterior Chimney

Figure 12.2 - Prefabricated Interior Chimney

A.  Venting Components 

Chimney Connector:

It is also known as flue pipe or appliance pipe.  The chimney 

connector joins the appliance to the chimney.  It must be a 6 

inch (152mm) minimum diameter 24 gauge mild steel black 

or 26 gauge blued steel, or an approved air-insulated double 

wall venting pipe.  

Thimble

:  

A manufactured or site-constructed device installed in 

combustible walls through which the chimney connector 

passes  to  the  chimney.    It  is  intended  to  keep  the  walls 

from  igniting.    Site  constructed  thimbles  must  meet  NFPA 

211 Standards.  Prefabricated must be suitable for use with 

selected chimney and meet UL103 Type HT Standards.  Follow 

instructions provided by the manufacturer for manufactured 

thimbles for masonry chimney and prefabricated chimneys.

Chimney

:

The chimney can be new or existing, masonry or prefabricated 

and must meet the following minimum requirements specified 

in Section 5B.

B.  Chimney Systems

Prefabricated Metal Chimney

•  Must be minimum 6 inch (152mm) diameter (ID) high 

temperature chimney listed to UL 103 HT (2100

o

F) or 

ULC S629M.

•  Must use components required by the manufacturer 

for installation.

•  Must maintain clearances required by the manufacturer 

for installation.

•  Refer to manufacturers instructions for installation.

Summary of Contents for EXPLR-III-MBK





















Reviews: