background image

 12 

 

 

 

 

                        7062-197G 

 

 

                   August 13, 2018

Explorer I

3 ft (91 cm)

Minimum

Less than 10 ft (305 cm)

2 ft (61 cm)

3 ft (91 cm)

Minimum

10 ft (305 cm) To Nearest Roofline

2 ft (61 cm)

Pitched Roof

Figure 12.1

Figure 12.2

10 ft. (305cm) or more

3 ft. (91cm) Minimum

Less than 10 ft. (305cm)

2 ft. (61cm) Minimum

3 ft. (91cm) Minimum

Wall or Parapet

Flat Roof

C. 2-10-3 Rule 

These are safety requirements and are not meant to 

assure proper flue draft.

This appliance is made with a 6 inch (152mm) diameter 

chimney connector as the flue collar on the appliance.

•  Changing the diameter of the chimney can affect draft 

and cause poor performance.

• 

It is not recommended to use offsets and elbows at 

altitudes above 4000 feet above sea level and or when 

there are other factors that affect flue draft.

B. Chimney Termination Requirements

Follow manufacturer’s instructions for clearance, securing 

flashing and terminating the chimney (

Figure 12.1 & 12.2).

•  Must have an approved and Listed cap

•  Must not be located where it will become plugged by 

snow or other material

•  Must terminate at least 3 feet (91cm) above the roof 

and

 at least 2 feet (61cm) above any portion of the roof 

within 10 feet (305cm).

•  Must be located away from trees or other structures

NOTICE:

•  Chimney performance may vary.

•  Trees, buildings, roof lines and wind conditions affect 

performance.

•  Chimney height may need adjustment if smoking or 

overdraft occurs.

NOTICE: 

 LOCATING THE APPLIANCE IN A BASEMENT 

OR  IN A  LOCATION  OF  CONSIDERABLE AIR 

MOVEMENT  CAN  CAUSE  INTERMITTENT 

SMOKE SPILLAGE FROM APPLIANCE. DO NOT 

LOCATE APPLIANCE NEAR

•  Frequently open doors

•  Central heat outlets or returns

Summary of Contents for EXPLORER I























Reviews: