Quadra-Fire DISCOVERY-II-C Owner'S Manual Operation & Care Download Page 2

2

7033-353G

08/21

1

7033-354

SERIAL RATING PLATE

1

7.75

9.5

LISTED ROOM APPLIANCE, SOLID FUEL TYPE. ALSO FOR USE IN MOBILE HOMES. (UM) 84 HUD . 

"For Use with 

Solid Wood Fuel Only"

 / APPAREIL DE CHAUFFAGE DE PIÈCE, DE TYPE DE COMBUSTIBLE SOLIDE, POUR USAGE 

DANS LES MAISONS MOBILES. (UM) 84 HUD. 

"Pour Usage Avec Bois Solide Seulement"

PREVENT HOUSE FIRES / PRÉVENTION DES FEUX DE MAISON

Install and use only in accordance with manufacturer's installation and operating instructions. Contact local building or fire 

officials about restrictions and installation inspections in your area. Do not obstruct the space beneath appliance. 

WARNING 

- For Mobile Homes:

 Do not install in a sleeping room. An outside combustion air inlet must be provided and unrestricted 

while unit is in use. The structural integrity of the mobile home floor, ceiling and walls must be maintained. The appliance 

needs to be properly grounded to the frame of the mobile home. Components required for mobile home installation: Outside 

Air Kit, Part Number OAK-ACC. 

Refer to manufacturer's instructions

 and local codes for precautions required for passing 

chimney through a combustible wall or ceiling and maximum offsets. Inspect and clean chimney frequently - Under Certain 

Conditions of Use, Creosote Buildup May Occur Rapidly. Do not connect this unit to a chimney serving another appliance. 

Optional Blower, Part BK-ACC. Electrical Rating: 115 VAC, 1.2 Amps, 60 Hz. Route power cord away from unit. Do not route 

cord under or in front of appliance. 

DANGER: Risk of electrical shock.

 Disconnect power supply before servicing. Replace 

glass only with 5mm ceramic available from your dealer. Do not use grate or elevate fire. Build wood fire directly on hearth. 

Do not overfire - if appliance or chimney connector glows, you are overfiring. Operate only with the fuel loading door closed. 

Open only to add fuel to the fire. / Installez et utilisez en accord avec les instructions d'installation et d'opération du fabricant. 

Contactez le bureau de la construction ou le bureau des incendies au sujet des restrictions et des inspections d'installation 

dans votre voisinage. Ne pas obstruez l'espace en dessous de l'appareil. 

AVIS - Pour Les Maisons Mobiles :

 Ne pas 

installer dans une chambre à coucher. Un tuyau extérieur de combustion d'air doit être installé et ne doit pas être obstrué 

lorsque l'appareil est en usage. La structure intégrale du plancher, du plafond et des murs de la maison mobile doit être 

maintenue intacte. L'appareil de chauffage doit être fixé à la charpente de la maison mobile. Les composants requis pour 

l'installation des maisons mobiles: Assemblage d'air extérieur, Numéro de Pièce OAK-ACC. 

Référez vous aux instructions

 

du fabricant et des codes locaux pour les précautions requises pour passer une cheminée à travers un mur ou un plafond 

combustibles, et les compensations maximums. Inspectez et nettoyez la cheminée fréquemment. Sous certaines conditions, 

il se peut que la créosote s'accumule rapidement. Ne pas connecter cet appareil à une cheminée servant un autre appareil. 

tVentilateur Optionnel, Pièce BK-ACC. Puissance Électrique: 115 VAC, 1.2 Amps, 60 Hz. Éloignez le fil électrique de 

l'appareil. Ne pas faire passer le fil électrique au dessus ou en dessous de l'appareil. 

DANGER : Il y a risque de décharge 

électrique.

 Déconnectez le fil électrique de la prise de contact avant le service. Remplacez la vitre seulement avec une vitre 

céramique de 5 mm disponible chez votre fournisseur. N'élevez pas le feu. Bâtissez le feu de bois directement sur l'âtre. Ne 

pas surchauffer. Si l'appareil de chauffage ou le tuyau de cheminée rougissent, vous surchauffez. Opérez l'appareil 

seulement lorsque la porte de chargement est fermée. Ouvrez la porte seulement lorsque vous devez ajouter des 

combustibles dans le feu.

CAUTION

:

 

U.S. ENVIRONMENTAL PROTECTION AGENCY

Certified to comply with 2020 particulate emission standards using crib wood at 

1.9

 G/HR 

This wood heater needs periodic inspection and repair for proper operation. Consult the 

owner’s manual for further information. It is against federal regulations to operate this wood 

heater in a manner inconsistent with the operating instructions in the owner’s manual.

2021

2022

Dec.

Nov.

Oct.

Sept.

Aug.

July

June

May

Apr.

Mar.

Feb.

Jan.

2023

FLOOR PROTECTION:

Floor protector must be a 3/8 (9.5mm) inch min. thickness, 

non-combustible material or equivalent, extending beneath 

heater and to front/sides/rear as indicated on the diagram 

below. 

Exception:

 Non-combustible floor protections must 

extend beneath the flue pipe when installed with horizontal 

venting and extend 2 inches (51mm) beyond each side.

HOT WHILE IN OPERATION DO NOT TOUCH, KEEP CHILDREN AND CLOTHING AWAY. CONTACT MAY CAUSE SKIN BURNS. KEEP FURNISHINGS 

AND OTHER COMBUSTIBLE MATERIAL FAR AWAY FROM THE APPLIANCE. SEE NAMEPLATE AND INSTRUCTIONS.

VENT SPECIFICATIONS: / SPÉCIFICATIONS DE LA VENTILATION :
SINGLE WALL:

 Six inch (6 inches) (152mm) diameter, minimum 24 MSG black or blued steel connector pipe, with a listed factory-built UL103HT* Class "A" chimney, suitable for use with solid fuels, or a masonry chimney, and the referenced clearances. 

MUR SIMPLE :

 De six (6 inches) (152mm) de diamètre le connecteur de conduit de minimum d'acier noir ou bleu de minimum de 24MSG, avec une cheminée bâtit en usine UL103HT* de Classe "A", adéquate pour usage avec les combustions solides, 

ou une cheminée de briques, avec espaces libres référés.

DOUBLE WALL:

 Six inch (6 inches) (152mm) diameter, listed double wall air insulated connector pipe with listed factory-built UL103HT* Class "A" chimney, or  a masonry chimney and the referenced clearances. / 

MUR DOUBLE :

 De six (6 inches) 

(152mm) de diamètre, le connecteur du conduit d'air isolé pour mur double avec une cheminée bâtit en usine UL103HT* de Classe "A:, ou une cheminée de briques, avec espaces libres alloués.

MOBILE HOME:

 Use double wall pipe by Dura-Vent DVL, Selkirk Metalbestos DS or Security DL double wall connector pipe. Must be equipped with a spark arrestor.  Apply double wall clearances below when installing unit. / 

MAISON MOBILE :

 Utiliser 

un conduit de mur double par Dura-Vent DVL, Selkirk Metalbestos DS ou Security DL. Doit être équipé d'un arrêt d'étincelle. Utiliser les espaces libres pour mur double comme mentionné ci-bas.

MINIMUM CLEARANCES TO COMBUSTIBLE MATERIALS: In Inches & (Millimeters) / ESPACES LIBRES MINIMUM DES MATÉRIAUX COMBUSTIBLES:En Pouces & (millimètres)

NOTE: All "A" , "C" and "F" Dimensions are to inside diameter of the flue collar. / REMARQUE : Toutes les dimensions "A", "C", et "F" sont à partir du diamètre intérieur de l'entrée du conduit.

7033-354E

CHAUD LORS DE L'OPÉRATION. NE PAS TOUCHER. GARDEZ LES ENFANTS ET LES VÊTEMENTS LOIN DE L'ESPACE DÉSIGNÉ DE L'INSTALLATION. LE CONTACT PEUT CAUSER DES 

BRÛLURES À LA PEAU. GARDEZ LES MEUBLES ET LES MATÉRIAUX COMBUSTIBLES LOIN DE L'ESPACE DÉSIGNÉ DE L'APPAREIL. VOIR L'ÉTIQUETTE ET LES INSTRUCTIONS.

ATTENTION:

PROTECTION DU PLANCHER:

Le protecteur de plancher doit être d'un minimum de 3/8 

inch (9.5mm) d'épaisseur, de matériel incombustible ou 

équivalent, s'étendant du dessous de l'appareil de 

chauffage à l'avant, aux cotés et à l'arrière comme indiqué 

sur le diagramme suivant. 

Exception :

 Les protections 

incombustibles du plancher doivent s'étendre en dessous 

du conduit de cheminée lorsqu'installées avec une 

ventilation à l'horizontale et s'étendre de 2 inches (51mm) 

de chaque côté.

DO NOT REMOVE THIS LABEL / NE PAS ENLEVER L'ÉTIQUETTE

Manufactured by:

Fabriqué par :

CANADA

203mm (8")

203mm

(8")

203mm

(8")

457mm (18")

1243mm

(49")

minimum

1041mm (41") minimum

Made in U.S.A. 

of US and imported parts. 

/ Fabriqué aux États-Unis-d’Amérique par 

des pièces d’origine américaine et pièces 

importées.

31M-ACC-C

DISCOVERY-II-C

352 Mountain House Road, 

Halifax, PA 17032

www.quadrafire.com

Serial No. / N° de série

HF

BARCODE LABEL

TESTED TO:/ TESTÉ À :

ASTM E2515, ASTM E2780, UL 1482-11 (R2015), ULC S627-00.

R

3100 ACC Series-C

Report / Rapport

0061WS066S

0061WS066E

16" from glass

8"
USA

Fuel loading door

Millennium 31-5/8" Min

39”

minimum

INSTALLATION: FULL VERTICAL OR HORIZONTAL WITH MINIMUM 2 FT VERTICAL OFF STOVE TOP / INSTALLATION : ENTIÈREMENT VERTICALE OU HORIZONTALE AVEC 609mm VERTICAL MINIMUM DU HAUT DU POÊLE

SINGLE WALL PIPE / CONDUIT DU MUR SIMPLE 

A  B 

C  D E  F  G  H

Discovery-II-C

 

18.25 (464) 

11.75 (298) 

28.5 (724) 

16 (406) 

8 (203) 

20 (508) 

48 (1220) 

12 (305)

31M-ACC-C

 

18.25 (464) 

11.75 (298) 

28.5 (724) 

16 (406) 

8 (203) 

20 (508) 

48 (1220) 

12 (305)

DOUBLE WALL PIPE / CONDUIT DU MUR DOUBLE

Discovery-II-C

 

13.5 (343) 

6.5 (165) 

25 (635) 

13 (330) 

6.5 (165) 

18.5 (470) 

48 (1220) 

9 (229)

31M-ACC-C

 

13.5 (343) 

6.5 (165) 

25 (635) 

13 (330) 

6.5 (165) 

18.5 (470) 

48 (1220) 

9 (229)

INSTALLATION:  90° ELBOW OFF TOP OF STOVE THROUGH BACKWALL / INSTALLATION:  90° DU COURBURE AU DESSUS DE HAUT DU POÊLE A TRAVERS LE MUR ARRIÈRE

SINGLE WALL PIPE / CONDUIT DU MUR SIMPLE

Discovery-II-C

 

15 (381) 

8.5 (216) 

25 (635) 

13 (330) 

8 (203) 

20 (508) 

48 (1220) 

12 (305)

31M-ACC-C

 

15 (381) 

8.5 (216) 

25 (635) 

13 (330) 

8 (203) 

20 (508) 

48 (1220) 

12 (305)

DOUBLE WALL PIPE / CONDUIT DU MUR DOUBLE

Discovery-II-C

 

11 (279) 

4.5 (114) 

20.5 (521) 

8.5 (216) 

6.5 (165) 

18.5 (470) 

48 (1220) 

9 (229)

31M-ACC-C

 

11 (279) 

4.5 (114) 

20.5 (521) 

8.5 (216) 

6.5 (165) 

18.5 (470) 

48 (1220) 

9 (229)

INSTALLATION: ALCOVE

 - Six inch (6 inches) (152mm) diameter listed DOUBLE WALL air insulated connector pipe with UL103 HT** listed factory-built Class "A" chimney, or a masonry chimney. (Mobile Home must be equipped with a 

spark arrestor.) Maximum depth of Alcove shall be no more than 48 inches (1219mm) and the referenced alcove clearances. / 

INSTALLATION : ALCÔVE

 - Six pouces (6 pouces) (152mm) de diamètre listé air isolé tuyau de 

raccordement à double paroi avec UL103 HT ** cotée Classe usine construite "A" cheminée ou une cheminée de maçonnerie. (Mobile Home doit être équipé d' un pare-étincelles.) Profondeur maximale de Alcove ne doit pas être plus de 

48 pouces (1219mm) et les dégagements en alcôve référencés.

DOUBLE WALL PIPE / CONDUIT DU MUR DOUBLE

Discovery-II-C

 

14.75 (375) 

8.25 (210) 

26.5 (673) 

14.5 (368) 

N/A 

N/A 

48 (1220) 

*

31M-ACC-C

 

14.75 (375) 

8.25 (210) 

26.5 (673) 

14.5 (368) 

N/A 

N/A 

48 (1220) 

*

*In Canada must comply with Standard CAN/ULC-S629-M87 for the 650°C Factory-built chimney. / *Au Canada doit conformer a CAN/ULC-S629-M87 la norme pour 650°C cheminée bâtit en usine.

* SEE PIPE MANUFACTURERS CLEARANCES - NOT TESTED / VOIR LE FABRICANT POUR LES ESPACES LIBRES DES CONDUIT - PAS TESTÉ

90° OFF TOP 

UP & OUT CEILING CLEARANCE

ESPACE LIBRE DU DESSUS DE 

L'APPAREIL AU PLAFOND AVEC 

90°  DE COURBURE 

STOVE TO CEILING CLEARANCE

ESPACE LIBRE DU POÊLE AU 

PLAFOND 

G

G

H

G

A

B

ALCOVE SIDE VIEW / 

VUE DE CÔTÉ DE 

L'ALCÔVE

B

G

A

ALCOVE TOP VIEW /

VUE DU HAUT DE 

L'ALCÔVE 

C

D

BACKWALL/SIDEWALL

MUR ARRIÈRE/MUR DE CÔTÉ 

A

B

C

D

CORNER INSTALLATION/

INSTALLATION DU COIN 

E

F

E

F

SAMPLE

Serial

 No.

Safety & 

Emissions  

Test 

Report 

Name

Test Lab & 

Report No.

Mfg. Date

A. Sample of Serial Number / Safety Label 

LOCATION:  Back of appliance

NOTE:

 Clearances may only be reduced by means approved by the regulatory 

authority having jurisdiction

and Welcome to the Quadra-Fire Family

!

Model 

Numbers

Summary of Contents for DISCOVERY-II-C



































Reviews: