background image

Quadra-Fire • Adventure-III Installation Manual • 4083-901 • Rev B • 05/15

2

TABLE OF CONTENTS

     Safety Alert Key:

• 

DANGER!

 

Indicates a hazardous situation which, if not avoided will result in death or serious injury.

• 

WARNING!

 Indicates a hazardous situation which, if not avoided may result in death or serious injury.

• 

CAUTION!

 

Indicates a hazardous situation which, if not avoided, may result in minor or moderate injury.

• 

NOTICE:

 Indicates practices which may cause damage to the appliance or to property.

Quadra-Fire is a registered trademark of Hearth & Home Technologies.

Important Safety Information ............3

A.  Appliance Certification ......................................................3

B.  BTU & Efficiency Specifications........................................3

C.  Mobile Home Approved .................................................... 3

D.  Glass Specifications .........................................................3

E. Non-Combustible Materials ...............................................3

F. Combustible Materials ........................................................3

Getting Started ...................................4

A. Design and Installation Considerations ..................................4

B. Fire Safety .........................................................................4

C.  Negative Pressure  ...........................................................5

D.  Tools And Supplies Needed ..............................................5

E.  Inspect Appliance and Components .................................5

F. Install Checklist ..................................................................6

Dimensions and Clearances .............7

A.  Appliance Dimensions ......................................................7

B. Clearances to Combustibles ..............................................8

C.  Hearth Protection Requirements.......................................9

D.  Locating Your Appliance & Chimney.................................10

E.  Chimney Termination Requirements .................................10

F.  2-10-3 Rule .......................................................................11

Chimney Systems ............................12

A.  Venting Systems  ..............................................................12

B.  Chimney Systems .............................................................13

C.  Chimney Height / Rise and Run .......................................13

D. Installing Chimney Components ........................................13

E.  Factory-Built Chimney ......................................................14

F.  Masonry Chimney .............................................................15

G. Masonry Chimney Liner ....................................................16

H.  Securing Chimney Components .......................................17

Appliance Set-Up .............................18

A.  Door Assembly  ................................................................18

B. Thermostat Installation  .....................................................19

C.  Fan (Optional)...................................................................20

D.  Outside Air Kit Installation.................................................21

Mobile Home Installation .................22

Accessory List .................................23

Summary of Contents for Adventure-III

























Reviews: