background image

January 

13, 

2020     7047-910J 

     

9

5100 Insert ACC

SIDE

 TRIM

SIDE

 W

ALL

TOP TRIM

27-1/4

692mm

32-1/4

819mm

HEARTH 

EXTENSION

USA 16-3/4

CANADA 

24-3/4 (629mm)

40-11/16

1033mm

FIREPLA

CE  FR

ONT SURF

ACE

USA 23-1/2

CANADA 25-1/2 (648mm)

HEARTH EXTENSION

43-11/16

1110mm

12in max

MANTEL

No thermal protection required

ember protection only

C

D

A

B

Minimum Opening Dimensions

Inches

Millimeters

A

Height

22-1/4

565

B

Front Width

29-3/8

746

C

Back Width

25-3/4

654

D Depth

17-7/8

454

B. Clearances to Combustibles

United States and Canada (UL and ULC)

In Canada a full length 6 inch (152mm) S635 flue liner required as per ULC S628.

In USA a minimum 5 ft length (1.82m), 6 inch (152mm) diameter flue liner is required as per UL 1482.

NOTE:

 Minimum opening dimensions include a 1/4” 

(6mm) clearance around unit.

NOTE:

 

If trim measurement is over 3/4 in (19mm) 

in depth use mantle or side clearances to 

combustibles.

NOTE:

 Clearances may only be reduced by means 

approved by the regulatory authority having 

jurisdiction

Fire Risk.

• 

Comply with all minimum clearances to 

combustibles as specified.

• 

Failure to comply may cause house fire.

WARNING

Summary of Contents for 51I-ACC-BK



























Reviews: