background image

 14 

      7047-910J 

   

January 

13, 

2020

5100 Insert ACC

• 

Must meet minimum standards of 

NFPA 211

.

• 

Must have at least 5/8 inch (16mm) fire clay lining 

joined with refractory cement.   (Installations into a clay 

flue without a stainless steel liner may reduce draw 

which affects performance, will cause the glass to 

darken and produce excessive creosote).

• 

The masonry wall of the chimney, if brick or modular 

block, must be a minimum of 4 inches (102mm) 

nominal thickness.

• 

A chimney of rubble stone must be at least 12 inches 

(305mm) thick.

• 

Cross-sectional area shall conform to 

NFPA 211-2006 

Section 12.4.5.1

.

• 

Should be lined with a 6 inch (152mm) stainless steel 

flue liner to improve performance and reduce creosote 

build-up.

I. Masonry Chimney

UL 1777 Insulated Stainless Steel 

Liner or Other Approved Lining System 

Follow Manufacturer’s Instructions 

on Insulation and Support 

For Zero or Other Non-Code Clearances, 

Follow Approved Liner Manufacturer’s Specific 

Insulation Requirements:  Different Clearances 

May Require Different Specifications 

Masonry Chimney Must 

Have Structural Integrity 

UL 1777 Insulated Stainless Steel 

Liner or Other Approved Lining System 

Minimum 8 in. (203mm) Masonry 

Thickness in Front of Smoke Chamber

Damper Plate Removed or 

Fastened in Open Position 

Seal with Non-Combustible Material 

Minimum Clearance in Accordance 

with Insert Listing 

Floor Protection in 

Accordance with Insert 

Listing 

Follow Manufacturer’s 

Instructions for Maximum 

Liner Extension Above 

Chimney 

Maximum 30

 

Degrees 

Offset in Chimney 

Combustible Floor 

Figure 14.1

NOTE:

 In Canada, this fireplace insert must be installed 

with a continuous chimney liner of a 6 inch 

(152mm) diameter extending from the fireplace 

insert to the top of the chimney.  The chimney 

liner must conform to the Class 3 requirements 

of 

CAN/ULC-S635

, Standard for Lining Systems 

for Existing Masonry or Factory-Built Chimneys 

and Vents, or 

CAN/ULC-S640

, Standard for 

Lining Systems for New Masonry Chimneys.

Generic Insert Model Shown in Illustration

This insert conforms with the 

UL 1482 and ULC S628 

(Canada)

 in all respects, and is approved to 

UL & 

ULC safety standards

 for installation and use within 

a fireplace with a masonry chimney in accordance with 

NFPA 211 and CAN/CSA-B365-01

.

• 

An equivalent liner must be a listed chimney liner 

system or other approved material.

• 

No dilution air is allowed to enter the chimney.

a. 

Secure the fireplace damper in the open position.  

If this cannot be accomplished, it will be necessary 

to remove the damper.

b.  Seal damper area of chimney around chimney 

connector with a high temperature sealant or seal 

insert against the face of the fireplace.

c. 

Both methods must be removable and replaceable 

for cleaning and re-installation.

• 

When possible, install an airtight clean-out door to the 

rear of the smoke shelf.

Summary of Contents for 51I-ACC-BK



























Reviews: