Quadra-Fire 4300 Series Owner'S Manual Download

Page: 1 / 52

www.quadrafi re.com

7037-135L

August 3, 2015

DO NOT DISCARD THIS MANUAL

CAUTION

•

Important operating
and maintenance in-
structions included.

• Leave this manual with

party responsible for
use and operation.

• Read, understand and

follow these instructions
for safe installation and
operation.

WARNING

If the information in these instruc-
tions is not followed exactly, a fi re
may result causing property dam-
age, personal injury, or death.

• Do not store or use gasoline or other fl am-

mable vapors and liquids in the vicinity of
this or any other appliance.

• Do not overfi re - If heater or chimney con-

nector glows, you are overfi ring. Overfi ring
will void your warranty.

• Comply with all minimum clearances to

combustibles as specifi ed. Failure to
comply may cause house fi re.

Fire Risk.

WARNING

For use with solid wood fuel only.
Other fuels may overfi re and generate
poisonous gases (i.e. carbon monoxide).

Installation and service of this appliance should
be performed by qualifi ed personnel. Hearth &
Home Technologies recommends NFI certifi ed
professionals, or technicians supervised by an
NFI certifi ed professional.

WARNING

Hot glass will cause burns.

•  Do not touch glass until it is cooled
•  NEVER allow children to touch glass
•  Keep children away
•  CAREFULLY SUPERVISE children in same room

as fi replace.

• Alert children and adults to hazards of high

temperatures.

High temperatures may ignite clothing or other
fl ammable materials.

• Keep clothing, furniture, draperies and other

fl ammable materials away.

HOT SURFACES!

Glass and other surfaces are
hot during operation AND
cool down.

To obtain a French translation of this manual, please
contact your dealer or visit www.quadrafi re.com

Pour obtenir une traduction française de ce manuel,
s’il vous plaît contacter votre revendeur ou visitez
www.quadrafi re.com

NOTE

4300 WOOD STOVE SERIES

Automatic Combustion Control (ACC)

Owner’s Manual

Installation and Operation

Models:

43M-ACC-MBK

43ST-ACC

Millennium Model

Step Top Uni-Body Model

(Pedestal Model Shown)

Summary of Contents for 4300 Series





















































Search results

Summary of Contents for 4300 Series

Reviews:

Related manuals for 4300 Series

Brands by name

Popular brands

Quadra-Fire 4300 Series, Owner'S Manual

Search results

Summary of Contents for 4300 Series

Reviews:

Related manuals for 4300 Series

Brands by name

Popular brands