manualshive.com logo in svg

Quaddrix QT-500 Series, User Manual, Page: 127 / 128

Share
Download
Quaddrix QT-500 Series User Manual Download Page 127

 
 

2)

 

Real board of DVR 
has problems. 

3)

 

Main board of DVR 
has problems. 

Cannot find the hard disk in reboot 
process. 

1)

 

Hard disk cable is 
broken. 

2)

 

The power cable of 
hard disk is not 
connected. 

3)

 

Hard disk is broken.  

No response in HyperTerminal interface.   1)

 

Baud rate is not 
matched. 

2)

 

RS-232 cable is 
broken. 

3)

 

Serial port of PC is 
broken. 

4)

 

RS-232 port of DVR 
is broken. 

DVR can not control PTZ through RS-485 
port. 

1)

 

RS-485 cable is not 
connected correctly 
or broken. 

2)

 

PTZ parameters 
error. 

3)

 

RS-485 port of DVR 
is broken. 

Client software can not view DVR live 
image.  

1)

 

Network is error. 

2)

 

Connect wrong DVR 
(wrong IP, port 
number, username 
or password, etc). 

3)

 

Need to upgrade to 
a newer client SW 
version. 

 

Notes: 

Summary of Contents for QT-500 Series

































































































































Reviews:

No comments