background image

EXPLANATION OF GRAPHICAL SYMBOLS

The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of uninsu-
lated “dangerous voltage” within the product’s enclosure that
may be of sufficient magnitude to constitute a risk of electric
shock to humans.

The exclamation point within an equilateral triangle is intended
to alert the users to the presence of important operating and
maintenance (servicing) instructions in the literature accompa-
nying the product.

CAUTION: To reduce the risk of electric shock, do not
remove the cover. No user-serviceable parts inside.
Refer servicing to qualified service personnel.

WARNING: To prevent fire or electric shock, do not
expose this equipment to rain or moisture.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

Federal
Communications
Commission (FCC)

Information

NOTE: This equipment has been tested

and found to comply with the limits for a

Class B digital device, pursuant to Part 15

of the FCC Rules. These limits are de-

signed to provide reasonable protection

against harmful interference in a com-

mercial installation. This equipment gen-

erates, uses, and can radiate radio fre-

quency energy and, if not installed and

used in accordance with the instructions,

may cause harmful interference to radio

communications. Operation of this equip-

ment in a residential area is likely to

cause harmful interference, in which case

the user will be required to correct the

interference at his or her own expense.

4

SAFEGUARDS

Electrical energy can perform many useful functions. This unit

has been engineered and manufactured to assure your personal

safety. Improper use can result in potential electrical shock or fire

hazards. In order not to defeat the safeguards, observe the

following instructions for its installation, use and servicing.

IMPORTANT SAFETY INFORMATION: PLEASE REVIEW!

WARNING!

WHILE QSC HAS ENDEAVORED TO DEVELOP AND PRODUCE THE MOST DEPENDABLE AND ROBUST DIGITAL SIGNAL

PROCESSOR (DSP) AUDIO PRODUCT FOR YOUR USE, DUE TO THE UNLIMITED AND POTENTIALLY DESTRUCTIVE (TO THE

SOUND SYSTEM) CONFIGURATIONS THAT MAY BE APPLIED TO THE DSP BY THE USER, QSC CANNOT BE HELD RESPON-

SIBLE FOR DAMAGES RESULTING FROM ANY DEVIATION OR FAILURE BY THE USER TO STRICTLY FOLLOW THE RECOM-

MENDATIONS SET FORTH IN THE OWNER’S MANUAL FOR THE  INTEGRATION OF THE DSP-3 AND SIGNAL MANAGER

SOFTWARE WITH YOUR SOUND SYSTEM.

ALL RISKS ATTENDANT TO INTEGRATION OF USER-CONFIGURABLE DSP PRODUCTS WITH YOUR SOUND SYSTEM ARE

ASSUMED BY YOU.  WHILE QSC STRIVES TO SUPPLY THE HIGHEST QUALITY TECHNICAL SOLUTIONS FOR DIGITAL SIGNAL

PROCESSING, IN NO EVENT WILL QSC OR ITS SUPPLIERS BE HELD LIABLE FOR ANY DAMAGES, CONSEQUENTIAL,

INCIDENTAL, OR OTHERWISE, INCLUDING ANY CLAIMS FOR LOST PROFITS AND/OR SAVINGS RESULTING FROM ANY

ATTEMPTED INTEGRATION OF THE DSP-3 AND SIGNAL MANAGER SOFTWARE WHICH DOES NOT STRICTLY ADHERE TO

THE MANUAL’S RECOMMENDATIONS.

Summary of Contents for DSP-3'





































Reviews: