background image

Attero Tech by QSC

 unBT2A 

User Manual 

 

 

 QSC, LLC 2020 

 

614-00034 

8.1 – Device Specification 

 
 

 

Physical Dimensions (unBT2A) 

Width 

1.7" 

Height 

4.2" 

Depth 

1.2" 

Weight 

0.2 lbs. 

Physical Dimensions (unBT2A-EXP) 

Width 

5.75" 

Height 

1.125" 

Depth 

1.625" 

Weight 

0.15 lbs.  

Product Compliance 

FCC CFR 47 Parts 15B Class A 
ICES-003 
CE (EN55022) 
RoHS  
REACH 

Other 

Temperature: 

0 – 40° C 

Power Consumption 

<100mA @ 24V (< 2.4W) 

Audio Inputs 

 

Input Types: 

Stereo Bluetooth® v3.0 audio 
receiver 
(A2DP Profile only) 

Range 

Approx. 10m (30ft) minimum 

Audio Outputs

 

Output Type:

 

Two balanced line level with 
automatic muting on loss of 
A2DP audio stream 
Phoenix-style 3.81mm de-
pluggable terminal blocks 

Output 
Sensitivity 

+4 dBu / -10dBV  
Software switchable 

Output 
Impedance: 

200 Ohms balanced, 
100 Ohms unbalanced 

Maximum 
Output 
Levels: 

+20 dBu (+4dBu Pro Mode) 
+6dBu a (-10dB – Consumer 
mode)) 

Max Cable  
Length 

100 meters, 24 AWG UTP 

Audio Output Performance

 

Dynamic 
Range:

 

>87 dB 

THD+N: 

<0.05% @ 1kHz, input signal 
3dB below maximum 

Frequency 
Response 

20Hz – 20kHz, +1dB /- 3dB 

RS-232 Port

 

Baud Rate:

 

9600 bps 

Data Bits 

Parity  

None 

Stop Bit 

Max Cable  
Length 

100 meters, 24 AWG UTP 

Summary of Contents for ATTEROTECH unBT2A

















Reviews: