background image

42

 

©  Copyright 2018 QSAN Technology, Inc. All Rights Reserved.

 

 

 

 

5.

 

Restart/Shutdown/Logout QSM 

 

If you want to restart, shutdown or log out QSM, please follow the steps below:

 

1.

 

To restart or shutdown QSM, please click on the QSAN logo on the top left corner, then 
choose the option which you would like to proceed. Click Yes button on the confirm window.

 

 

2.

 

To log out QSM, please click User Profile on the top right corner, then choose Logout. Click 
Yes button on the confirm window.

 

 

 
 

6.

 

to Default 

 

If you want to reset XCubeNXT to factory default, there are several options to choose from. Please 
follow the steps below:

 

Reset to default by using the reset button on the back of XCubeNXT:

 

 

 

 

1.

 

Reset network settings: Press and hold the reset button on the rear panel for 3 seconds, a short 
beep sound for 1 second will be heard. The administrator password and all the network settings 
will be reset, the system configuration will result in: 

 

Reset Admin password to the default value: 1234.

 

 

All networking set to "DHCP".

 

 

All data service ports set to default setting (All data service enable and set to default 

port).

 

 

VLAN will be terminated.

 

 

Vswitch will be deleted.

 

 

Port trunking will be disabling.

 

 

After configs are deleted, restart the XCubeNXT.

 

 

Log out QSAN Cloud.

 

 

DNS settings.

 

 

DDNS and UPNP settings.

 

Summary of Contents for XCubeNXT XN8000D






































































Reviews: