QNAP TES-1885U-D1521-16GR Hardware User Manual Download | Manualshive

Page: 33 / 50

background image

33

The chart below describes the events of an error when using RAID 5.

RAID 5 (Minimum 3 Disks)

QTS

Standard

One drive fails

Degraded mode (may still read

and write).

Degraded mode (may still read

and write).

One drive fails

and there are bad

sectors found in

the other drive(s)

Read only protect mode (for

immediate data backup & hard

drive replacement).

RAID crash.

2 hard drives fail

RAID crash.

RAID crash.

The chart below describes the events of an error when using RAID 6.

RAID 6 (Minimum 4 Disks)

QTS

Standard

One or two drives

drive fail

Degraded mode. (may still read

and write).

Degraded mode. (may still read

and write).

Two drives fail

and there are bad

sectors found in

the other drive(s)

Read only protect mode (for

immediate data backup & hard

drive replacement).

RAID crash.

3 hard drives fail

RAID crash.

RAID crash.

«
...
31
32
33
34
35
...
»

Summary of Contents for TES-1885U-D1521-16GR



















































Reviews:

No comments

Related manuals for TES-1885U-D1521-16GR

Brand: IBM Pages: 252

Brand: eMachines Pages: 46

Brand: AZZA Pages: 12

Brand: Hitachi Pages: 123

Brand: Hitachi Pages: 194

Brand: Hitachi Pages: 197

Brand: Hitachi Pages: 227

Brand: Hitachi Pages: 1153

Precision 3640 Tower

Brand: Dell Pages: 112

Brand: Toshiba Pages: 217

Satellite A100 Series

Brand: Toshiba Pages: 294

Satellite A300 Series

Brand: Toshiba Pages: 263

Satellite A20 Series

Brand: Toshiba Pages: 495

Satellite 1400 Series

Brand: Toshiba Pages: 528

Brand: HP Pages: 1

Brand: HP Pages: 5

Brand: HP Pages: 5

s3330f - Pavilion - Slimline

Brand: HP Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands