QNAP TES-1885U-D1521-16GR Hardware User Manual Download | Manualshive

Page: 15 / 50

background image

15

Chapter 3.

LED and Alarm Buzzer Specifications

3.1

LED

The LED indicators of the NAS indicate the system status and information. When the NAS is
turned on, check the following items to make sure the system status is normal. Note that
the following LED information is applicable only when users have properly installed the hard
drive, and connected the NAS to the network and the power supply.

«
...
13
14
15
16
17
...
»

Summary of Contents for TES-1885U-D1521-16GR



















































Reviews:

No comments

Related manuals for TES-1885U-D1521-16GR

Brand: IBM Pages: 48

Brand: IEI Technology Pages: 131

PowerBox 310 Series

Brand: Spectra Pages: 116

Brand: DeskBook Pages: 104

Brand: Acer Pages: 101

Brand: Dell Pages: 36

Brand: Fanvil Pages: 6

Brand: Fluke Pages: 122

Brand: Sokkia Pages: 60

Brand: Sokkia Pages: 68

Brand: Cybernet Pages: 47

Pro-Face PL-6900 Series

Brand: Digital Electronics Corporation Pages: 105

kontron COMe-cVR6

Brand: S&T Pages: 90

Brand: Shuttle Pages: 1

Brand: Viglen Pages: 2

Brand: RadiSys Pages: 122

Brand: Dynamic Pages: 141

Brand: Faytech Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands