background image

9

'(+>p

If[Wa[hekjfkj

.&>p

<kbbHWd][

3UBINDEPENDANTSTEREOMODE

H

Lebkc[

B

&

&

'

'

&

A

G

'

2.  Sub + independent stereo  

mode with alternative  
passive speakers

This configuration allows the operator to connect 

alternative satellite speakers and reset the cross-

over frequencies from full range to 80 Hz or 120 

Hz depending on the type of satellite speaker the 

operator wishes to use. Completely independent 

volume control of the satellite speakers is also 

possible in this mode

The input mode switch

This switch configures the QM 1000 mid/high unit 

for use through the Aux1 & 2 Volume controls. 

Select full-range mode for 12” speakers, 80 Hz for 

10” and 8” speakers or select a higher crossover 

frequency for lower powered satellite speaker 

boxes under 150 watts RMS. 

The Aux volume controls will now function 

independently from the master volume control.

1

   Set Input mode switch to AUX.

2

   Select volume to max.

3

    Connect right and left XLR outputs to AUX 

input 1 and 2 with XLR patch leads.

4

    Select the low cut filter AUX 1 and 2 to full 

range/80Hz/125Hz depending on your choice 

of satellite speakers. 8” speakers function 

best with the high pass filter set to 80 or 

125Hz. 10” speakers should be set to 125Hz. 

12” speakers can be set to 80Hz or full range.

5

    Aux 1 and 2 volume now controls the output 

level of each auxillery amplifier.

6

    High cut ajusts the cross-over frequency of 

the sub bass set below 100Hz for low bass 

seperation from satellite speakers.

7

    Normal Sub Rev Sub bass phase/polarity 

reversal switch. Some brands of speaker 

boxes are wired reverse polarity to the 

standard. When using speakers of a different 

brand to Quest Engineering you may operate 

this switch to see which setting sounds best 

with your speakers. If not sure, leave “in 

phase”

8

    Sub woofer volume. To ajust volume level of 

sub bass, operate the control knob.

9

    Speaker outputs. Connect speakers. Do 

not allow speaker output left and right to 

be connected together when connecting 

multiple speakers.

'(+>p

If[Wa[hekjfkj

.&>p

<kbbHWd][

3UBINDEPENDANTSTEREOMODE

H

Lebkc[

B

&

&

'

'

&

A

G

'

1

2

3

3

4

5

6

7

8

Summary of Contents for QM 1000AS

















Reviews: