background image

A – Fast!UTIL

Configuration Settings

DC8151101-00 C

A-3

Safe. All optimal configuration settings are disabled and all attached 
devices work in minimal configuration (narrow, asynchronous mode).

NOTE: Safe mode is primarily for troubleshooting SCSI devices that 

are not functioning properly during normal system operation.

Drivers Load RISC Code. When this setting is Enabled, the QLA12160 
board uses the RISC firmware that is embedded in the software driver. When 
this setting is Disabled, the software driver loads the latest version of RISC 
firmware found on the system. The default is Enabled.

NOTE: The driver being loaded must support this setting; otherwise, the 

result is the same as Disabled regardless of the setting. Leaving 
this option Enabled guarantees a certified combination of software 
driver and RISC firmware.

>4 Gbyte Addressing. Enable this setting when your system has more 
than 4 GB of RAM available. The default is Disabled.

Fast Command Posting. When this setting is Enabled, command execution 
time is decreased by minimizing the number of interrupts. The default is 
Enabled.

A.2.2

SCSI Device Settings

After changing the host adapter settings for the QLA12160 board, you can modify 
device parameters for SCSI devices connected to the board. From the 
Configuration Settings menu in Fast!UTIL, select SCSI Device Settings. The 
settings are linked to the device’s SCSI ID (0–15). If you make changes, be sure 
that the SCSI ID matches the settings of the device you want to change. Select 
Scan SCSI Bus from the Fast!UTIL Options menu to see the SCSI IDs assigned 
on your system 

(see section A.3)

.

NOTE: The Adapter Configuration setting in the Host Adapter Settings 

(see 

section A.2.1)

 controls which device settings you can change.

The options and defaults for SCSI device settings are listed in 

table A-2

 and 

described in the following paragraphs.

Table A-2. SCSI Device Settings 

Setting

Options

Default

Adapter Configuration 

Setting

Disconnects OK

Yes, No

Yes

Auto, Safe, Manual

Check Parity 

Yes, No

Yes

Auto, Safe, Manual

Enable LUNs

Yes, No

Yes

Auto, Safe, Manual

Enable PPR

Yes, No

Yes

Manual

Get other manuals https://www.bkmanuals.com

Summary of Contents for QLA12160































Reviews: