background image

Configuration Settings

A – Fast!UTIL

A-2

DC8151101-00 C

A.2.1

Host Adapter Settings

From the Configuration Settings menu in Fast!UTIL, select Host Adapter 
Settings
. Default settings for the QLA12160 host adapter board are listed in 

table A-1

 and described in the following paragraphs.

Host adapter BIOS. When this setting is Disabled, the ROM BIOS on the 
QLA12160 board is disabled, freeing space in upper memory. The RAM 
BIOS and other drivers still recognize the QLA12160 board. Do not disable 
this setting when you are booting from a SCSI disk drive attached to the 
QLA12160 board. The default is Enabled (ROM BIOS on the QLA12160 
board is enabled).

PCI bus DMA burst. When this setting is Enabled, burst transfers are 
performed. When this setting is Disabled, data is transferred in nonburst 
mode, with each cycle initiated by a new address phase. The default is 
Enabled.

CDROM Boot. When this setting is Enabled, the ROM BIOS boots from the 
attached SCSI CD-ROM when a bootable compact disk is installed. If no 
bootable CD-ROM is found, the system boots from the first bootable SCSI 
drive. When this setting is disabled, the ROM BIOS does not boot from the 
CD-ROM. The default is Disabled.

Adapter Configuration

Auto. The ROM BIOS automatically configures the QLA12160 board to 
match any SCSI device attached to the board and selects optimum 
performance. The default is Auto.

Manual. You can control the configuration settings for each SCSI device 
and have the option of running Autoconfigure. 

See section A.2.4

 to have 

Fast!UTIL configure the devices.

NOTE: Changing any value can cause performance problems or 

incorrect device operation.

Table A-1. Host Adapter Settings

Setting

Options

Default

Host adapterBIOS

Enabled, Disabled

Enabled

PCI bus DMA burst

Enabled, Disabled

Enabled

CDROM Boot

Enabled, Disabled

Disabled

Adapter Configuration

Auto, Manual, Safe

Auto

Drivers load RISC code

Enabled, Disabled

Enabled

>4 Gbyte Addressing

Enabled, Disabled

Disabled

Fast Command Posting

Enabled, Disabled

Enabled

Get other manuals https://www.bkmanuals.com

Summary of Contents for QLA12160































Reviews: