background image

 

 

19

Installation And Operation Manual 

For 

DTPO610VC 

 

 

 

Make  sure  that  tool  trays,  stands  or  persons  are  removed  or  evacuated  from  under  vehicle.

  ●

 

 

Lower vehicle by activating lowering handle.

 

 

 

Before  removing  vehicle  from  lift  area,  position  the  lift  arms  and  the  supports  to  provide 

an 

unobstructed exit.

 

 

NEVER, drive over lift arms.  

 

 

 

REQUIRED MONTHLY UPKEEP  

 

 

Check arm restrains for proper operation.

 

 

Check all chain/cable connections, bolts and pins to ensure proper mounting.

 

 

Visually inspect safeties for proper operation.

 

 

Lubricate columns with grease.

 

 

Inspect all anchor bolts and retighten if necessary.

 

 

Check columns for squareness and erectness.

 

 

Inspect all arm pivot pins to make sure that they are all properly secured.

 

 

Check the tensions of equalizer cables, adjust if necessary.

 

 

Inspect all lift pads, replace if necessary.

 

 

If lift is equipped with overhead cut-off switch, check for proper operation. 

 

 

 

                  

WARNING 

 

 

 

1.

 

If cement anchor bolts are loose, or any component of the lift is found to be defective, DO NOT USE 
LIFT. 

 

2.

 

Never operate the lift with any person or equipment below. 

 

3.

 

Never exceed rated capacity. 

 

4.

 

Always ensure that safeties are engaged before any attempt to work on or near the lift. 

 

5.

 

Never leave lift in an elevated position unless the safeties are engaged. 

 

6.

 

Do not permit electric motor to be damp! Motor damage caused by dampness is not covered under 
the warranty. 

 

 

 

 

 

 

NEVER  LIFT  ANY  VEHICLE  IN  ANY  MANNER  WITH  LESS  THAN  FOUR  (4)  ARMS. 

RATED CAPACITY OF EACH LIFT ARM IS NOT GREATER THAN ONE FOURTH (1/4) 
OF THE OVERALL LIFTING CAPACITY. 

 

Summary of Contents for DTPO610VC























Reviews: