q-Tech OLT-QSW-9010 Cli Configuration Manual Download Page 33

Page: 33 / 101

User Manual

3. Remote ONU function configuration

www.qtech.ru

OLT (config-gpon-onu12 / 4: 1) #remote onu mgmt-ip 11.0.0.2
255.255.255.0 11.0.0.1 vlan 101

Ping the ONU IP from OLT:

OLT # ping 11.0.0.2
!!!!!

VLAN 101 configured in uplink port can be forwarded to PC, thus switching to the EOC configuration
management.

3.15.

PON Port Isolation function Disabling

This function closes the isolation function so that interworking between the same VLAN of the PON
port ONU can be achieved.

When ONUs under different PON ports need service interworking, each of the corresponding PON
port needs to disable this function.

OLT(config-gpon-olt1/1)# switch-port protected disable

Summary of Contents for OLT-QSW-9010






































































































Search results

Summary of Contents for OLT-QSW-9010

Reviews:

Related manuals for OLT-QSW-9010

Brands by name

Popular brands

q-Tech OLT-QSW-9010, Cli Configuration Manual

Search results

Summary of Contents for OLT-QSW-9010

Reviews:

Related manuals for OLT-QSW-9010

Brands by name

Popular brands