background image

QH32DVR4C User’s Manual 

 

51

 

Fig 5.18 Motion alarm handle setup 

Step 6: Motion alarm record channel setup: 

When a motion alarm occurs, you can trigger 

related  camera  to  start  to  record.  In  “Motion  Alarm  Handle”  menu,  you  can  select  one  or  more 

recording channels. Please use

ENTER

or

EDIT

key to change the flag into “

”enabled. 

 

Note:  In  order  to  make  the  cameras  start  recording,  in  “Recording”  menu  you  must  enable 

recording schedule and set “Rec Type” as “Motion Detection” or “Motion | Alarm”. Please refer to 

Chapter 5.12 for recording setup.

 

 

Step 7: Motion alarm schedule: 

When a motion alarm occurs during a schedule, the DVR 

will  respond  with  a  “On  Screen  Warning”,  “Audible  Warning”,  “Upload  to  Center”  or  “Trigger 

Alarm Output” depending on your setup. You can setup 4 time periods for one day and 7 days for 

one week.   

 

Note: Time periods in one day can not be repeated.

   

 

Step 8: Motion alarm  handle  method setup: 

You can select one or  more handle methods 

such  as  “On  Screen  Warning”,  “Audible  Warning”,  “Upload  to  Center”  and  “Trigger  Alarm 

Output”.   

 

Description: If “On Screen Warning” is enabled, when a motion alarm occurs and the DVR is 

in preview mode, the DVR will switch to the related camera. If you trigger more than one camera, 

the DVR will pop them up one by one every 10 seconds. When the motion alarm ends, the DVR 

will return to preview mode.   

 

Summary of Contents for QSC26404 QH32DVR4C



























































































Reviews: