Pyranha SPRAYMASTER SM55 User Manual Download Page 16

Page: 16 / 16

SprayMaster® System User Manual | www.PyranhaInc.com | Houston, Texas

SprayMaster® Options & Replacement Products

Part Number

Description

002SMTOPONLY

SPRAYMASTER® SYSTEM TOP (MOTOR, TIMER, PUMP & BRASS CONNECTIONS)

002SM55GAL

SPRAYMASTER® - 55 GAL UNIT WITH BATTERY BACK UP

002SM55GALKIT

SPRAYMASTER® KIT - 55 GAL UNIT, (1) 1-10HP FILL, 160’ TUBING, 8 NOZZLES

004SNA1NPNS

SPRAY NOZZLE ASSEMBLY - 1/4” NICKLE PLATED BARREL, NICKLE SILVER TIP

004SNANPNSKIT

SPRAY NOZZLE ASSEMBLY KIT - (5) 1/4” NOZZLE ASSEMBLIES, 100’ TUBING

004NTUNUPKIT

TUNE-UP KIT - (2) 1/4” NOZZLES, 5 SPRAY TIPS, 1 INTAKE FILTER WITH TUBING

001HP55

PYRANHA® 1-10HP CONCENTRATE™ FOR 55 GALLON SYSTEM - 2.5 GAL

001HPS30

PYRANHA® 1-10HPS CONCENTRATE™ FOR 30 GALLON SYSTEM - 2.5 GAL

001ODAWAYC

PYRANHA ODAWAY™ ODOR ABSORBER - 1 GALLON

Rev. 121520

System_Manual_2020.indd 16

12/23/20 10:18 AM

Summary of Contents for SPRAYMASTER SM55

















Search results

Summary of Contents for SPRAYMASTER SM55

Reviews:

Related manuals for SPRAYMASTER SM55

Brands by name

Popular brands

Pyranha SPRAYMASTER SM55, User Manual

Search results

Summary of Contents for SPRAYMASTER SM55

Reviews:

Related manuals for SPRAYMASTER SM55

Brands by name

Popular brands