background image

Pinpoint

 

your finding

   

When there is a clear signal to show you the location of the buried target objects, you can make an “X” scan 
at this zone, generally the bottom of the intersection point is the target object. 
 

 

 
Pinpointing and PINPOINT Mode 

While searching in the motion mode, you should move the search coil evenly, consistently and persistently. 
However, if you run into an instance where you cannot determine exactly where to dig, or to narrow down 
the area, and determine a more exact location of the object, you can refer to the PINPOINT mode.   
 
 

Metal Detector Signals 

*Most valuable metal objects detected will send repeatable signals, as you scan over the ground surface area 
containing the object. If the signal is not repeated after your 're-scan' the ground floor surface area, it is most 
likely a false signal. When there is a clear sound instructing the buried targets, you can read out the 
approximate target type and depth on the LCD display screen. Then, hovering the search coil over the target 
object again can confirm the presence of a metal object. Along with the visual indication, the metal detector 
will provide audible frequency tones -- that also insist the presence of a detected metal object.   
 

Depth and Target Indication (only in the motion mode) 

Depending on the operation mode selected, the LCD digital display screen will show the predicted metal 
target types and the estimated target depth. When in neutral soil environments, the discrimination indication 
is more accurate, while in the mineralization or the discrimination indication will have various degrees of 
deviation. 
 

Caution 

In areas with heavy traffic, please do not wear earphones while detecting, in case an accident occurs. 
Always obtain permission before searching any site. 
Keep away from the areas that may have buried electrical or gas lines / cables.   
Do not detect in private property, military owned areas or where you do not receive permission to detect. 
When digging out the target, use a reasonable digging method that will not damage or cause harm to 
yourself or any possible object within the surface area.   
Try your best as to not destroy the vegetation, cause damage to any animals / insects.     
Take care of mother nature!   

www.PyleAudio.com 

Summary of Contents for PHMD72















Reviews: