PVI VECOAX ULTRA RF Series User Manual Download Page 6 | Manualshive

Page: 6 / 56

background image

Pro Video Instruments

VeCOAX Ultra RF Series user Manual

5

Selected
Channel
Advanced
Menu

Set your s

tandard you require to use. If you are unsure most newer TV’s 3 years and above accept

both ATSC (over the air channel) and QAM(J.83B Digital Cable).

Please Refer to your TV owner’s

manual

6.

By default, the unit is set to QAM (J.83B Digital Cable) Mode |Preset 1 |
with a Frequency of 303.000 MHz which is Channel 37 for the first channel
input. The TV will Scan for the Frequency and pick up the channels on Cable.
Depend on your model will determine the channels picked up.

7.

Auto Scan for Channels on your TV. Depending on your Location and
Supported TV standards for your TV such as QAM (J.83B Digital Cable) or
ATSC (Digital over the Air) will determine the Standard you need to set on
the unit. Please Refer to

CUSTOMIZATION

below to change these settings.

«
...
4
5
6
7
8
...
»

Summary of Contents for VECOAX ULTRA RF Series

























































Reviews:

No comments

Related manuals for VECOAX ULTRA RF Series

Brand: Ortek Pages: 13

Brand: Datexx Pages: 1

Brand: Datexx Pages: 1

DeskPilot DF-560

Brand: Datexx Pages: 1

Brand: Datexx Pages: 1

Brand: Datexx Pages: 15

Brand: Lemco Pages: 22

Brand: Olympia Pages: 2

Brand: GSS Pages: 40

Brand: QM Pages: 2

HDbridge 2000 Series

Brand: ZeeVee Pages: 7

Brand: eastern Pages: 15

Brand: Canon Pages: 2

Brand: GSS Pages: 42

watch any where Double

Brand: JollyLine Pages: 12

Brand: dig-MOD Pages: 20

Brand: Braun Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands