PVI VECOAX ULTRA RF Series User Manual Download

Page: 2 / 56

Pro Video Instruments

VeCOAX Ultra RF Series user Manual

NOTE: BEFORE INSTALLATION

Please test each unit

UNMOUNTED ON A TEST BENCH

with your Test

TV before installing your units to ensure you are receiving the Test

Pattern signal. Then Program your unit.

This makes troubleshooting easier.

This can be done simply by connecting your TV with a short piece of
Coax cable to the RF out of the Unit.

No HDMI needs to be connected

for this test

This will display our test pattern on your TV once you scan for digital

By default, our unit is set to QAM (J.83B Cable) mode.

This can be changed by referring to our

QUICK GUIDE

below.

Depending on your supported TV standards, scan for digital channels.

Please refer below for our

QUICK GUIDE

to setting up your device for

your application and needs.

Summary of Contents for VECOAX ULTRA RF Series

























































Search results

Summary of Contents for VECOAX ULTRA RF Series

Reviews:

Related manuals for VECOAX ULTRA RF Series

Brands by name

Popular brands

PVI VECOAX ULTRA RF Series, User Manual

Search results

Summary of Contents for VECOAX ULTRA RF Series

Reviews:

Related manuals for VECOAX ULTRA RF Series

Brands by name

Popular brands