background image

 
 
PVA Warranty Policy       

         

 

 
 
 

PVA warrants the enclosed product against defects in material or workmanship on 

all components for one year from the date of shipment. 
 

The warranty does not extend to components damaged due to misuse, negligence, 

or installation and operation that is not in accordance with the recommended factory 
instructions.  Unauthorized repair or modification of the enclosed product, and/or the use 
of spare parts not directly obtained from PVA (or from factory authorized dealers) will 
void all warranties. 
 

All PVA warranties extend only to the original purchaser.  Third party warranty 

claims will not be honored at any time. 
 

Prior to returning a product for a warranty claim, a return authorization must be 

obtained from PVA’s customer service department.  Authorization will be issued either 
via the telephone, facsimile, or in writing upon your request. 
 

To qualify as a valid warranty claim, the defective product must be returned to the 

factory during the warranty period.  Upon return, PVA will repair (or replace) all 
components found to be defective in material or workmanship. 

 
 
 
 

(Retain this for your records)

 

 
Product Information:

 

 
PRODUCT:  

______________________________ 

 
 
SERIAL NUMBER: 

______________________________ 

 
 
DATE OF PURCHASE:  ______________________________

 

 

 

Summary of Contents for FC100-CF1













Reviews: