PV Electronics Nixie 5750 Assembly Instructions And User Manual Download Page 38

Page: 38 / 48

Nixie Tube Clock ‘Nixie 5750’

Issue 1 (5 July 2020)

www.pvelectronics.co.uk

- 38 -

9.4

Time Synchronisation Function

XTERNA broadcasts every 10 minutes. After configuring your clock,
please be patient in waiting for the first Synchronisation. Upon

synchronisation the yellow LED D7 will illuminate. Remember to set
DST (‘Summer Time’) with the DST button.

9.5

Temperature Display

The temperature is also transmitted with the time. Therefore,
temperature will not be displayed until after the first

synchronisation.
Set Celsius or Fahrenheit using parameter 29:

Fahrenheit: 1
Celsius : 2

Temperature is displayed between 30 and 35 seconds past each

minute. Celsius is displayed with 0.5 °C resolution. Fahrenheit is
displayed with 1 °F resolution.
Positive and negative temperature is indicated by the left hand

neons: Neon indicator PM2 acts as a decimal point.

9.6

Temperature Validity

If no valid data is received on the next scheduled sync (every 10
minutes), the temperature will be deemed to be old and invalid.

Temperature will not be shown until a new valid temperature is
received.

Summary of Contents for Nixie 5750

















































Search results

Summary of Contents for Nixie 5750

Reviews:

Related manuals for Nixie 5750

Brands by name

Popular brands

PV Electronics Nixie 5750, Assembly Instructions And User Manual

Search results

Summary of Contents for Nixie 5750

Reviews:

Related manuals for Nixie 5750

Brands by name

Popular brands