background image

 

 

 

 

 

 

    AWS1100 Wet Sander Manual                                          1

Copyright   PushCorp, Inc. 2000.  All rights reserved.

1.0 Limited Warranty

Duration:

One year from date of delivery to the original purchaser.

Who gives this warranty (warrantor):

PushCorp, Inc.
Telephone: (972) 840-0208

Corporate Address:
P. O. Box 181915
Dallas, Texas 75218

Shipping Address:
3001 W. Kingsley Rd.
Garland, Texas 75041

Who receives this warranty (purchaser):

The original purchaser (other than for purposes of resale) of the PushCorp, Inc.
product

What products are covered by this warranty:

Any  PushCorp,  Inc.  industrial  equipment  or  accessory  supplied  or
manufactured by the Warrantor.

What is covered under this warranty:

Defects in material and/or workmanship, which occur within the duration of the
warranty period.

What is NOT covered in this warranty:

A.

IMPLIED  WARRANTIES,  INCLUDING  THOSE  OF  MERCHANT-ABILITY
AND FITNESS FOR  A  PARTICULAR  PURPOSE  ARE  LIMITED  TO  ONE
YEAR FROM THE DATE OF ORIGINAL PURCHASE.  Some states do not
allow  limitations  on  how  long  an  implied  warranty  lasts,  so  the  above
limitations may not apply to you.

B.

ANY  INCIDENTAL,  INDIRECT,  OR  CONSEQUENTIAL  LOSS,  DAMAGE
or  EXPENSE  THAT  MAY  RESULT  FROM  ANY  DEFECT,  FAILURE,
MALFUNCTION OF THE PUSHCORP, INC. PRODUCT.  Some states do
not allow the exclusion or limitation of incidental or consequential damages
so the above limitation or exclusion may not apply to you.

C. Any  failure  that  results  from  an  accident,  purchaser's  abuse,  neglect,

unauthorized  repair  or  failure  to  operate  the  products  in  accordance  with
the  instructions  provided  in  the  owner's  manual(s)  supplied  with  the
product.

Responsibilities of the Warrantor under this warranty:

Repair  or  replace,  at  Warrantor's  option,  products  or  components  which  have
failed within the duration of the warranty period.

Summary of Contents for AFD1100













Reviews: