background image

User Manual

 

PT-C-HDCEC 

 

 

1.

 

Product Introduction 

Thanks for choosing the PT-C-HDCEC 18G In-line HDMI Controller, which is designed 
for automatic system control and HDMI signal extension in small meeting rooms and 
huddle spaces. The controller supports a variety of system trigger methods, via IR 
signal input or video signal detection (5V "Hot-Plug-Detect" or "TMDS sensing"). It 
automatically triggers CEC commands as well as pre-loaded RS232 and IR 
commands to turn on or off devices as well as relay control to lower and raise 
projection screens. It supports video resolutions up to 4K@60Hz 4:4:4 with HDR 10 
and Dolby Vision support and is capable of 4K to 1080p down-scaling, for 
compatibility with 1080p display devices. Besides passing EDID information from 
the display, there are multiple built-in EDID settings that can be selected using the 
4-pin DIP switch on the front panel. In addition, the controller supports CEC 
pass-through, RS232 control, IR learning and relay control. 
 

1.1

 

Features 

 

Supports up to 4K@60Hz, 4:4:4 with HDR10 and Dolby Vision support, HDCP 2.2 
compliant. 

 

HDCP pass-through or conversion to HDCP 1.4 for better compatibility. 

 

Supports 4K to 1080p down-scaling. 

 

Comprehensive EDID management with 8 EDID options for various applications. 

 

Display control options via CEC, RS232 and IR. 

 

Contact closure input for the connection with a variety of periphals, such as 
sensors and switches. 

 

Relay control, e. g. for lowering and raising projection screens. 

 

Built-in signal equalizer for longer HDMI cable runs. 

 

 

Summary of Contents for PT-C-HDCEC





























Reviews: