background image

8

 

Installation & Operation Manual

Copyright © Puretec Pty Ltd 2020

Initial Installation Procedure

The Puretec WU-UV Series has 1" [25mm] plumbing connections.

1.  Before attempting installation check the unit to ensure the quartz sleeve is intact 

within the Radfire UV Unit.

2.  Locate a suitable position for the WU-UV system remembering to allow 120mm 

under units with 20" housings and 700mm clearance above the unit for cartridge 
and lamp changes. A power outlet is required.

Installation Procedure

Fig. 1

700mm clearance

700mm clearance

WU-UV 100 / 150  MODELS

WU-UV 200 / 250 MODELS

3. 

WU-UV units have 4 mounting 

provisions. 2 key holes at the front 
and rear of the bracket. Mark the 
desired position on the wall where the 

fixings are required to go.

4.  Drill the holes and install the anchors 

(fixing anchors not included).

SHEET

DESCRIPTION

REV.

MATERIAL

WEIGHT

TREATMENT

SCALE

3RD ANGLE 

PROJECTION

APPROVED BY

DATE

DATE

MODIFICATIONS

REV.

DRAWN BY

DRAWN BY

SUPPLY SPECIFICATION

DERIVED FROM

1 / 1

1 : 1

PETER KENNEDY

ROSS BUTCHER

304 GRADE STAINLESS STEEL

NATURAL

N/A

800 g

A

INTRODUCTION

25/02/2020

25/02/2020

PETER KENNEDY

N/A

A

DIMENSIONS ARE IN MILLIMETRES

0     +- 1.0mm

0.0    +- 0.5mm

0.00   +- 0.1mm

ANGLES:

DIMS.

0     +- 1.0deg.

A

B

C

D

E

F

G

H

10

10

9

9

8

8

7

7

6

6

5

5

4

4

3

3

2

2

1

1

 NUMBER

NAME

PHK 5000 - 5

HOUSING

HOUSING UV CHAMBER HYBRID G SERIES

APPROVED BY

DATE

MODIFICATIONS

REV.

DRAWN BY

SUPPLY SPECIFICATION

DERIVED FROM

PETER KENNEDY

ROSS BUTCHER

N/A

A

INTRODUCTION

25/02/2020

N/A

DIMENSIONS ARE IN MILLIMETRES

DO NOT SCALE

0     +- 1.0mm

0.0    +- 0.5mm

0.00   +- 0.1mm

ANGLES:

DIMS.

0     +- 1.0deg.

A

B

C

D

E

F

G

H

12

12

11

11

10

10

9

9

8

8

7

7

6

6

5

5

4

4

A2

allow min. 120mm clearance from the ground

Fig. 2

Summary of Contents for WU-UV Series





















Reviews: