customerservice
@
puregbi.com
1-866-498-5269
MODEL# 9011TS - PAGE 10
C-Hook
ASSEMBLY INSTRUCTIONS
Step 9:
Attach all 36 Springs Hook ends
(Part #7) using the Spring Loading
Tool (Part #16) to all Top Rail
Openings by following the correct
placement order. The R-Hook end
should be attached to Trampoline
Mat, and C-Hook to Top Rail.
For even distribution of tension
and ease of assembly, springs
should be placed on opposite
sides of the mat/frame. Attach
springs 1-18 in the correct
numerical order to properly
distribute tension of the mat.
Once the first 18 springs have
properly attached to all Top Rails,
install the remaining springs
to complete the instalation of
the trampoline mat onto the
foundation.
Step 10:
Tie down the all elastic straps
attached to the trampoline pad into
the the top rails tightly.
17
STEP 7
Lay out the Trampoline Mat with Safety Pad (#1) inside the frame with Safety Pad flip up as shown in FIGURE 7.
There are total of 36 Triangle-rings sewn on the mat, and 36 holes on the Top Rail Frame. None are numbered so please
follow the instructions carefully to ensure proper installation. Now, select an arbitrary point on the Top Rail Frame (call it
ZERO) as shown in FIGURE
7
.
SPRING LOADING INSTRUCTION
CAUTION
�
Make sure to flip up the safety pad for ease of installation of springs.
�
Two adults are required in this assembling step.
�
CAREFUL - When attaching the springs, please do not put your hands, legs, or body close to the connector points.
The connector points can become pinch points since the trampoline is tightening up.
�
Wear heavy duty working gloves to protect your hand.
�
Use the special spring loading tool included.
STEP 8
Attach the R-Hooked Galvanized Spring (#8) with
“
R
”
Hook end to the Triangle-Ring on the mat as shown below.
HINT:
Holding the spring at 45 degree in relation to the mat surface will be much easier to install into Triangle -Ring.
SPRING LOADING TOOL (9)
Hold the spring loading tool underhand and pull spring hook towards the point “ZERO” on the Top Rail frame as shown
in
FIGURE 8. Drop hook into frame hole until it latches on completely and tap it down if hook is not completely in the hole.
FIGURE 8
“
R
”
HOOK END
SPRING (#8)
POINT ZERO
SPRING LOADING TOOL(#9)
ZERO
FIGURE 7
18
Then, attach a springs at the Corners Top Rail (#3) first as shown in FIGURE 9. For even
distribution of tension and ease
of assembly, springs should be placed on opposite sides of the mat/frame
…
..i.e. 5, 6 then 23, 24; Zero, 35 then 17, 18, etc.
Now, you should have 12 springs install at ZERO, 5, 6, 11, 12, 17, 18, 23, 24, 29, 30, and 35.
STEP 9
Attach
a spring
at every 3 holes and corresponding Triangle-rings. For even
distribution of tension and ease of assembly,
springs should be placed on opposite sides of the mat/frame
…
..i.e. 3 then 21, 33 then 15, etc. In addition to the previously
installed springs, you should have springs at 3, 9, 15, 21, 27, and 33 as shown in FIGURE 10.
FIGURE
10
FIGURE 9
(#
1)
(#
1)
CAUTION:
If you notice that you have miscount a hole and Triangle-rings connection, recount and remove or attach any springs
required to maintain the count of springs.
18
18
Then, attach a springs at the Corners Top Rail (#3) first as shown in FIGURE 9. For even
distribution of tension and ease
of assembly, springs should be placed on opposite sides of the mat/frame
…
..i.e. 5, 6 then 23, 24; Zero, 35 then 17, 18, etc.
Now, you should have 12 springs install at ZERO, 5, 6, 11, 12, 17, 18, 23, 24, 29, 30, and 35.
STEP 9
Attach
a spring
at every 3 holes and corresponding Triangle-rings. For even
distribution of tension and ease of assembly,
springs should be placed on opposite sides of the mat/frame
…
..i.e. 3 then 21, 33 then 15, etc. In addition to the previously
installed springs, you should have springs at 3, 9, 15, 21, 27, and 33 as shown in FIGURE 10.
FIGURE
10
FIGURE 9
(#
1)
(#
1)
CAUTION:
If you notice that you have miscount a hole and Triangle-rings connection, recount and remove or attach any springs
required to maintain the count of springs.
18
19
STEP 10
Then, attach the remaining 18 springs by using the same theory of counting equal holes as shown in FIGURE11.
STEP 11
Flip down the Safety Pad stitched with the trampoline mat (#1). Pull tight the elastic straps over the frame as shown in
FIGURE 12 and make sure safety pad covers the frame.
Perform a complete inspection of the trampoline to make sure all parts are assembled and attached properly.
FIGURE 11
(#
1)
ELASTIC STRAP
Trampoline Pad
(In lift-up position)
FIGURE 12
Read this entire manual and make sure all jumpers completely understand all of the safety rules printed in the manual and
on the various warning signs. Instruct all jumpers in the basic bounces
described
in the manual.
!
IMPORTANT NOTICE:
Make sure the safety pad is securely attached to the frame and completely covers the
frame and all springs before using this trampoline. Do not use trampoline if even one spring or Triangle-ring is damaged or
missing.
1
2
3
4
5
7
8
9
10
11
12
13
14
15
16
17
18
6
19
STEP 10
Then, attach the remaining 18 springs by using the same theory of counting equal holes as shown in FIGURE11.
STEP 11
Flip down the Safety Pad stitched with the trampoline mat (#1). Pull tight the elastic straps over the frame as shown in
FIGURE 12 and make sure safety pad covers the frame.
Perform a complete inspection of the trampoline to make sure all parts are assembled and attached properly.
FIGURE 11
(#
1)
ELASTIC STRAP
Trampoline Pad
(In lift-up position)
FIGURE 12
Read this entire manual and make sure all jumpers completely understand all of the safety rules printed in the manual and
on the various warning signs. Instruct all jumpers in the basic bounces
described
in the manual.
!
IMPORTANT NOTICE:
Make sure the safety pad is securely attached to the frame and completely covers the
frame and all springs before using this trampoline. Do not use trampoline if even one spring or Triangle-ring is damaged or
missing.
PARTS NEEDED:
Trampoline Mat (Part #1), Spring Hook (Part #7), Spring Loading Tool (Part #16)
R-Hook
Opening
Spring(#7)
(#1)
(#1)
(#1)
Elastic Strap
Step 9
Step 10
