PumpSpy PS1000 Installation And Operating Instructions Manual Download Page 8

Limited Three-Year Warranty

WHAT THIS WARRANTY  COVERS

When used and maintained in normal use and in accordance with the Installation and Operating Instructions, your 
PumpSpy

™ 

product is warranted against original defects in material and workmanship for a full three years from 

date of purchase (the “Warranty Period”). During the warranty period, PumpSpy

 will repair or replace at no cost 

to you, to correct such defects in products found upon examination by PumpSpy

 to be defective in materials or 

workmanship.

WHAT THIS WARRANTY DOES NOT COVER

This warranty does not cover use of the product in a non-residential application, improper installation and/

or improper maintenance of the product, damage due to misuse, acts of God, nature, vandalism or other acts 
beyond the control of PumpSpy

, owner’s acts or omissions, use outside the country in which the product was 

initially purchased and resales of the product by the original owner. This warranty does not cover pick up, delivery, 
transportation or house calls. However, if you mail your product to PumpSpy

 for warranty service, cost of shipping 

will be paid one way. This warranty does not cover products purchased from a party that is not an authorized retailer, 

dealer, or distributor of PumpSpy

 products.

OTHER  IMPORTANT TERMS
This warranty is not transferable and may not be assigned. This warranty shall be governed and construed under 

the laws of the state of Ohio. The warranty period will not be extended by any replacement or repair performed 
under this warranty. THIS WARRANTY IS THE EXCLUSIVE WARRANTY AND REMEDY PROVIDED BY PumpSpy

ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WARRANTIES OR MERCHANTABILITY OR 

FITNESS FOR PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT WILL PumpSpy

 BE LIABLE FOR ANY 

SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND OR NATURE TO OWNER 

OR ANY PARTY CLAIMING THROUGH OWNER WHETHER BASED IN CONTRACT, NEGLIGENCE, TORT OR 
STRICT PRODUCTS LIABILITY OR ARISING FROM ANY CAUSE WHATSOEVER. Some states do not allow for the 

exclusion of consequential damages, so the above exclusion may not apply to you. This warranty gives you specific 

rights. You may also have others that vary state to state. 

Installed by:

Date of Installation:

Model :  

PS 1000

  

Serial Number:

© PumpSpy Technology, LLC   Questions? 

Call Tech Support: 515.999.6935

83019-03

Summary of Contents for PS1000









Reviews: