manualshive.com logo in svg

PumpSpy PS1000, Installation And Operating Instructions Manual, Page: 1 / 8

Share
Download
PumpSpy PS1000 Installation And Operating Instructions Manual Download Page 1

IMPORTANT !

READ ALL INSTRUCTIONS CONTAINED IN THIS MANUAL BEFORE USING THIS PRODUCT.

Save these instructions for future reference. Failure to read and follow the warnings and instructions within this instruction manual 

could result in property damage, serious injury or death.

INSTALLATION AND OPERATING INSTRUCTIONS

12 VDC Sump Pump

Power Supply Requirements 
Motor
AMP Rating
Temperature Rating
Discharge

MAX Flow 

12 VDC
Brushless DC 
18 Amps

40°F to 120°F
1 1/2” NPT
3000 GPH

System Solid State Pump Controller

Power Supply Requirements
Electrical Ratings

Relative Humidity

Storage Temperature
Operating Temperature

  

120 VAC, 60 Hz, 15 AMP

12Amps @ 120 VAC

18 Amps @ 12 VDC

0 to 80% 

0° to 70° C

0° to 50° C

SPECIFICATIONS

PumpSpy

™

 PS1000

PumpSpy™ | Tech Support:

 515.999.6935 | [email protected]

34000 LEAR INDUSTRIAL PARKWAY, AVON, OH 44011

®

PUMP

SPY

© PumpSpy Technology, LLC   Questions? 

Call Tech Support: 515.999.6935

The PumpSpy System requires a 12V Deep Cycle Battery with  

a minimum 75AMP/HR rating.  AGM Battery strongly recommended. 

 

Summary of Contents for PS1000









Reviews:

No comments