background image

2

Thank You for Purchasing this PSA Lifesaver Smoke Alarm

The smoke alarm you have purchased is capable of wirelessly interlinking with other Lifesaver 
6000DCW smoke alarms and Lifesaver 6000 series mains powered smoke alarm fitted with 6000WB 
wireless base, and 6000THL smoke alarm remote control. When one RF interlink unit sounds an alarm, 
all other compatible RF units in the RF interlink network will alarm, the red LED on Remote Control will 
blink. 

Read Section 6:

 Activation And RF Interlink Network, before powering the units. You do 

NOT need a home wi-fi system to use these units. Multiple wireless units create their own 
independent RF interlink alarm network.

This smoke alarm and included RF module are powered by a non-replaceable, long life sealed lithium 
battery system, which will last up to 10 years after power up (under normal operation).

NOTE: A NETWORK IS LIMITED TO 24 ALARMS

Teach children how to respond to the alarm and that they should never play with the unit.  
Your PSA LIFESAVER Smoke Alarm was designed for use in a residential environment. It is not designed 
for use in a recreational vehicle (RV) or boat.

Note: Please thoroughly read this user guide and save the document for future reference and 

to pass on to any subsequent owner. 
IMPORTANT: Additional markings can be found on the back or side of the unit.

 

Date Code (on back):  ___________________

 

Date of Purchase:  ___________________

 

Where Purchased:  ___________________

 

Date to Replace:  ___________________

Product Support: 1300 772 776

Please write down the following details, and 
have the information at hand when you call us

Summary of Contents for LIFESAVER 6000DCW




























Reviews: