background image

Page 10 

202-228-0300  PAR200B  

 Pilot Guide  

 

 

Bluetooth® Telephone Connection 

Before the PAR200B can be used in TELEPHONE mode with a wireless 

Bluetooth connection, the unit must be associated with a specific phone.

 

Activate the “seek device” function on the cell phone (if required, enter the 

access code “

0000

”) when the phone detects the “PAR200B” on the list of 

available devices. 
This process will be necessary for any phone to be used, and only one cell 

phone can be associated with the audio panel at a time. If the additional 

phones are associated with the PAR200B at the same time, only the 

first 

phone will transfer audio to the panel. 
If the Bluetooth connection fails to reconnect, or becomes unreliable for any 

reason, you can reset all connections through the user setup menu. This 

clears out all paired devices. 
PS Engineering recommends this clearing process if you are having difficul-

ties interfacing the PAR200B audio panel to your Bluetooth phone or device. 

Telephone Operation 

When the Bluetooth-enabled phone receives an incoming call, the PAR200B 

will play the ring tone from your phone. Answer the call by pushing the top 

line select button. The PAR200B exits the telephone mode automatically 

when the cellular phone hangs up, or the bottom line-select button is pushed. 
In TELEPHONE mode, the pilot microphone and headphones are connected 

to the cell phone. The pilot PTT will switch the pilot mic to the selected com 

transceiver, and allow continued aircraft communications to continue. 
The copilot will also be able to transmit on the other selected radio with his 

PTT as well. 
Entering the TEL mode connects the telephone to the users as follows: 

Summary of Contents for PAR200B

















Reviews: