manualshive.com logo in svg

PRÜFTECHNIK VIBXPERT Balancing, Operating Instructions Manual

Share
Download
PRÜFTECHNIK VIBXPERT Balancing Operating Instructions Manual Download Page 25

2-17

VIBXPERT Balancing 11.2010

Balancing: Evaluation

Evaluation of the data

The following data are listed in the data screen for each completed
balancing run:

- M

ASS

: Mass of the balancing weight

- A

NGLE

: Fixing angle

- V

IBRATION

: Vibration overall values (RMS)

- A

NGLE

: Phase angle

If you entered the rotor mass and the balancing radius, the achieved
balancing quality and the centrifugal force on the rotor are also
calculated. If the balancing quality is within the range of tolerance,
the "smiley" appears and indicates the end of the balancing proce-
dure.

Data View

• Press the MENU button in the data screen and click on "Data". The

"Data View" screen appears.

Here you can combine the balancing weights to a single weight and
display the following information:

- M

ACHINE

 

NAME

: Name of the machine setup if used

- D

ATE

 & 

TIME

:  Date and time of the last balancing run

- S

PEED

: Shaft rotational speed that is selected in the machine setup

- B

ALANCE

 

QUALITY

: Balance quality after the last balancing run

- R

ESIDUAL

 

UNBALANCE

: Imbalance after the last balancing run

The individual balancing runs can be activated in the list. The marked
run is highlighted in black in the polar diagram. A star (*) marks the
balancing runs in the list where the attached balancing weight was
removed again from the rotor after the measurement (e.g. trial run
with weight in plane B: ('1BB'), see figure below).

'Smiley'

*

*

*

Left:

Data screen

Balancing quality OK

Right:

Data View screen

Summary of Contents for VIBXPERT Balancing













































Reviews:

No comments

Brands by name

Popular brands

Load more brands