31
MARK76X1001 Rev 6
Guidance and Manufacturer’s Declaration - Electromagnetic Immunity
The Luxura Vegaz model 52X is intended for use in the electromagnetic environment specified below.
The customer or the user of the Vegaz model 52X should assure that it is used in such an environment.
Immunity Test
IEC 60601 Test Level
Compliance Test
Electromagnetic
Environment - Guidance
Electrostatic discharge
(ESD) IEC 61000-4-2
±2 kV, ±4 kV & ± 8 kV for
Contact Discharge
±2 kV, ±4 kV, ±8 kV and±
15kV for Air Discharge
±2 kV, ±4 kV & ± 8 kV for
Contact Discharge
±2 kV, ±4 kV, ±8 kV and±
15kV for Air Discharge
Floors should be wood,
concrete or ceramic tile.
If floors are covered with
synthetic material, the
relative humidity should be
at least 30%.
Electrical fast transient/
burst IEC 61000-4-4
±2kV for power supply lines
±1kV for input/output lines
±2kV for power supply lines
±1kV for input/output lines
Mains power quality
should be that of a typical
commercial or hospital
environment.
Surge IEC 61000-4-5
AC Mains Line to Ground
±0.5kV, ±1kV and ±2kV
AC Mains Line to Line
±0.5kV and ±1kV
AC Mains Line to Ground
±0.5kV, ±1kV and ±2kV
AC Mains Line to Line
±0.5kV and ±1kV
Mains power quality
should be that of a typical
commercial or hospital
environment.
NOTE:
1. UT is the a.c mains voltage prior to application of the test level.
2. Power frequency magnetic field test as described in EN61000-4-8 are not applicable. The
appliance doesn’t contain components which are sensitive to magnetic fields (e.g. Hall sensors)
3. Voltage Dips and Interruptions (IEC 61000-4-11) are not applicable because the rated input is
more than 16A per phase.
Guidance and Manufacturer’s Declaration – Electromagnetic Immunity
Non life supporting ME Equipment
The Luxura Vegaz model 52X
is intended for use in the electromagnetic environment specified below. The
customer or the user of the Luxura Vegaz model 52X should assure that it is used in such an environment.
Immunity Test
IEC 60601 Test
Level
Compliance
Level
Electromagnetic Environment – Guidance
Conducted RF
IEC 61000-4-6
AC Mains
3V with 6V ISM
80% AM at 1
kHz
150 kHz – 80
MHz
AC Mains
3V with 6V ISM
80% AM at 1
kHz
150 kHz – 80
MHz
Portable and mobile RF communications equipment should be
used no closer to any part of the ProSun Tanning Equipments,
including cables, than the recommended separation distance
calculated from the equation applicable to the frequency of the
transmitter.
Recommended separation distance
where P is the maximum output power rating of the transmitter in
watts (W) according to the transmitter manufacturer and d is the
recommended separation distance in metres (m).
Field strengths from fixed RF transmitters, as determined by an
electromagnetic site survey,a should be less than the compliance
level in each frequency range.b
Radiated RF
IEC 61000-4-3
3V/m,
80% AM at 1
kHz 80 MHz –
2700 MHz
(E1) = 3V/m
NOTE 1 At 80 MHz and 800 MHz, the higher frequency range applies.
NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection
from structures, objects and people
a Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and land mobile radios,
amateur radio, AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy. To assess
the electromagnetic environment due to fixed RF transmitters, an electromagnetic site survey should be considered. If the
measured field strength in the location in which the “Product Name” is used exceeds the applicable RF compliance level
above, the “Product Name” should be observed to verify normal operation. If abnormal performance is observed, additional
measures may be necessary, such as reorienting or relocating the “ProSun Tanning Equipments.
b Over the frequency range 150 kHz to 80 MHz, field strengths should be less than [V1] V/m.
Summary of Contents for Luxura X10/Vegaz 52
