manualshive.com logo in svg

Prostat PRS-801, User Manual

Share
Download
Prostat PRS-801 User Manual Download Page 16

16

Rev. C  / January 2012

PRS-812 Resistance Meter

F.  Properly dispose of any old batteries.

G.  Position the new alkaline battery under the battery cover.

H.  With your thumb, press the terminals in place one at a time.

I.  Carefully wind any excess battery lead around the battery terminal below the cap. To avoid instru-

ment damagae, do not pull battery connection leads

J.  Place the batteries back into position with the battery terminal covers  facing the lead spurce 

within the battery case shown in figure 4.

K.  Carefully position the instrument battery cover back into place without force.

L.  Replace the battery cover screws. 

M.  Slide battery buss switch to the 

ON

 position.

Following the above directions for battery replacement will insure that you do not damage the battery 

covers or wires during this process.

 

NOTE

 

It is recommended to measure the voltage of each battery with a multimeter. If the voltage of 

one battery measures at or below 6.75 volts, replace that battery. If both batteries measure at 

or below 6.75 volts, replace both batteries.

V.  Setup & Calibration

A.  Setting up the PRS-812 for low resistance range calibration

1.  Position Battery Buss Cut Off switch to OFF position 

2.  To install batteries, remove two Phillips locking screws and cover. Attach two Long-Life, Alkaline 

9V batteries to the battery connection terminals. 

3.  Position batteries in compartment with power leads neatly positioned above battery connec-

tions. Carefully re-install battery cover and locking screws.

NOTE

 

Do Not change batteries with the battery buss 

ON

. Always switch Battery Buss Cut Off to 

OFF

 

when changing batteries. Should the 

ON/OFF

 button be depressed during battery change and 

Battery Bus is 

ON

 the instrument may lock up and not function properly or be seriously dam-

aged. In this case, simply disconnect the batteries, then re-install with Battery Buss switch in 

the 

OFF

 position.

B.  Low Resistance Range (<10 Ohms) Calibration 

1.  Install the calibration shunt (PRS-801CC) across the Negative (-) and Positive (+) Lead Terminals 

(Figure 5, below). 

Summary of Contents for PRS-801









































Reviews:

No comments

Brands by name

Popular brands

Load more brands