manualshive.com logo in svg

Prostat PRS-801, User Manual

Share
Download
Prostat PRS-801 User Manual Download Page 15

15

Rev. C  / January 2012

PRS-812 Resistance Meter

Battery Compartment

Located in lower section of case, opposite LCD display. Holds two 9V-transistor batteries. Two 

screws secure the battery cover. Note: Use only Long Life Alkaline Batteries. Remove batteries 

when instrument is not in use for long periods of time. 

Figure 3: Opening Battery Compartment

Figure 4: Install 2 each 9V Alkaine 

Batteries

IV.  Battery Installation (See Figures 3 & 4)

For optimal battery life and avoid instrument damage, always replace the batteries with high energy, 

alkaline batteries. Failure to do so will result in a diminished battery life, measurement error and potential 

instrument damage that could void the warranty. 

The battery caps on the instruments you have purchased are designed to fit snugly. Please follow the di-

rections below for safe replacement of batteries.

A.  Slide battery bus switch to the 

OFF

 position (see figure 3). 

B.  Carefully remove the battery cover from the instrument.

C.  Gently take the batteries from the battery compartment.

D.  Unwind any battery lead that is wrapped around the top of the battery terminal. Do not pull bat-

tery connection leads - this could cause instrument damage.

E.  Very carefully place a flat head screwdriver between the battery terminals and gently lift the bat-

tery cover from the battery.

Battery Buss Switch 

MUST be off during 

battery change.

Summary of Contents for PRS-801









































Reviews:

No comments

Brands by name

Popular brands

Load more brands