background image

 

2. 

The fuse holder is located under the AC power receptacle, use the slotted (

–) 

screwdriver to loosen the fuse holder. 

3. 

Replace the fuse with new one. 

4. 

Put the fuse holder back in place. 

           

 

 

VII. 

Trouble shooting 

 

Warning:   

Before checking the inside of the SS-989 or replacing parts, be sure to 
disconnect the power plug. Failure to do so may result in electric shock.   

Defect Situation 

Possible Problem 

Solution 

Dead, Doesn’t work 

Blown fuse 

Change new fuse 
SS-989E(110V)    250V 8A 
SS-989B(220V)    250V 5A 
SS-989E7(127V) 250V 8A 
SS-989H(220V)    250V 5A 

PCB Board broken 

Contact vendor for repair 

Soldering Iron does

n’t 

heat up 

Panel display S-E, plug 

didn’t 

connect properly 

Reconnect the plug of Soldering Iron 

Heating Element broken 

Replacing heating element 

Heat Gun air 
Temperature 

doesn’t 

heat up 

Heating Element broken 

Replacing heating element 

Heat Gun airflow level 
abnormal     

Internal pipe 

obstruction or loosen 

caused air leakage

 

Clearing the internal pipe, reconnect the 
pipe tightly. 

Pump securing screws 

haven’t 

loosened 

Loosen the pump securing screw which 
on the bottom of control station. 

Display shows 
abnormal   

Transportation caused inside PCB 
board didn’t connect properly 

Open the case, reconnect the PCB 
board 

Input voltage lower than standard 
request 

Check with local power service provider 

Temperature unit 
display abnormal 

IC broken 

Contact vendor for repair 

Summary of Contents for SS-989




















Reviews: