background image

1. Basic parameters 

 

17

 

1.12.  Transportation conditions  

− 

Transportation of the robot must be carried out 
only in a specially designed case.

 

− 

The  robot  and  other  components  must  be  se-
curely fixed inside the case by special transporta-
tion  carrier.  The  vertical  position  of  the  robot 
must correspond to the transport marking "top" 
on the trunk (the robot must be packed upside

-

down  in  accordance  with  the  direction  of  the 
arrows  on  the  marking).  During  transportation, 
the  robot  must  be  turned  off.  Before  trans-
porting,  make  sure  that  the  robot  is  de

-

energized  by  moving  the  power  button  to  the 
"off" position.

 

− 

Before transporting, make sure that there are no 
foreign  objects  inside  of  the  compartment.  The 
presence  of  foreign  objects  can  damage  the  ro-
bot's parts.

 

− 

During transportation, the actuator should be in 
the  lowest  position,  and  the robot  body is  fixed 
in a fully rectified state.

 

− 

During  transportation,  the  robot  box  is  consid-
ered  to  be  a  fragile  freight.  Ensure  adequate 
transport  and  storage  conditions  for  the  entire 
transportation period.

 

 

   

 

 

Summary of Contents for V.4































































Reviews: