ProMinent alpha ALPc 0230 Operating Instructions Manual Download Page 40

13 

Decommissioning and disposal

13.1 

Decommissioning

Decommissioning

 WARNING!

Danger from chemical residue
There is normally chemical residue in

the liquid end and on the housing after

operation. This chemical residue could

be hazardous to people.

It is mandatory that the safety

information in the "Storage, trans‐

port and unpacking" chapter are

read before shipping or transport.

Thoroughly clean the liquid end

and the housing of chemicals and

dirt. Adhere to the material safety

data sheet for the feed chemical.

 WARNING!

Warning of hazardous feed chemical
Should a dangerous feed chemical be

used: it may escape from the hydraulic

components when working on the

pump, material failure or incorrect han‐

dling of the pump.

Take appropriate protective meas‐

ures before working on the pump

(e.g. safety glasses, safety

gloves, ...). Adhere to the material

safety data sheet for the feed

chemical.

Drain and flush the liquid end

before working on the pump.

 CAUTION!

Warning of feed chemical spraying

around
Feed chemical can spray out of the

hydraulic components if they are

manipulated or opened due to pressure

in the liquid end and adjacent parts of

the system.

Disconnect the pump from the

mains power supply and ensure

that it cannot be switched on again

by unauthorised persons.

Depressurise the system before

commencing any work on

hydraulic parts.

 Danger of damage to the device

Take into account the information in the

"Storage, transport and unpacking"

chapter if the system is decommis‐

sioned for a temporary period.

1.

Disconnect the pump from the mains/

power supply.

2.

De-pressurise the discharge line.

3.

Drain the liquid end by turning the pump

upside down and allowing the feed

chemical to run out.

4.

Flush the liquid end with a suitable

medium; flush the dosing head thor‐

oughly when using hazardous feed

chemicals!

Decommissioning and disposal

 

 

 

40

Summary of Contents for alpha ALPc 0230





















































Reviews: