Promac 378CLB Manual Download Page 4

1. Wear proper clothes while working. Do not wear any clothes that can easily be ripped by the machine         

while operating, such as clothes that flutter, ordinary gloves scarf, ring, and small chain. You should 

also wear anti-skid shoes and hat (cap) that can fully hold in long hairs. 

2. When operating this machine, you should wear a goggle and dust-proof mask anytime. Besides, make 

sure to abide to the related safety measures specified by the government’s Bureau of Works. 

3. Use a hand vice or other fixing device to fix all the spare parts for processing. Do not use your hands to 

fix them in order to avoid serious accident and unable to operate the said machine. 

4. Stand firmly in front of this machine while working (both feet’s position, body equilibrium, etc.) 

5. Keep the machine and its pointed edges clean at all time in order to get the best working efficiency. 

Also, should follow the instructions in the Instruction Manual carefully in changing the tools, coating 

grease, and cleaning.  

6. Before cleaning this machine or changing the tools (such as saw blade, drill),pull off the power plug first 

to avoid electrocution. 

7. Use the tools suggested by the manufacturer of this machine while working and abide to the related 

instruction in the Instruction Manual, because using spare parts not related to this machine is an 

unsafe behavior. 

8. Avoid touching the machine unintentionally. Also, before plugging in the plug into the socket, check if 

switch button is as 

OFF

position or not. 

9. Do not stand on the machine in order to avoid slipping down carelessly or hitting the blade and cause 

injury. 

10. Remember to check abnormal part in the running process of the machine carefully. 

It is advisable that you should change the said part or protective piece before continuing the work. 

11. Do not leave the working ground while the machine is running. It is necessary for your to leave, turn 

off the power and wait for the machine to stop completely before leaving. 

12. Do not use this machine if you had taken any alcohol (liquor or wine), medicine, or drugs. 

 

4

Summary of Contents for 378CLB






































Reviews: