Prolitec AirQ AQ1200 Original Instructions Manual Download Page 7

AQ/PS/RZ  1200

7

Chapter 4    

MOVING & STORAGE INSTRUCTIONS

Fragrance Cartridge Precautions 

• 

Use only AirQ by Prolitec fragrance cartridges.

• 

Read the Consumer Product Safety Information Sheet and the Material Safety Data Sheet provided 
with each shipment of Cartridges. Insure that these information sheets are available for review by 
employees.

• 

Use latex gloves to handle a Cartridge to avoid the liquid getting on hands. The AirQ fragrances 
are formulated so as to not be harmful in contact with the skin, but the concentrated nature of the 
fragrances may make the scent difficult to remove from hands and skin. 

• 

Wash your hands after all contact with Cartridges or fragrance.  

• 

While AirQ Air Treatment Agents do not contain ingredients deemed harmful to the skin, if there is skin 
contact, wash with soap and water. If there is contact with the eyes, irrigate the eye with fresh water for 
5 minutes. If there is any eye irritation, consult a physician immediately.

MOVING AND STORAGE INSTRUCTIONS

1.  Remove the cartridge.

2.  Unscrew and remove the long round-head screws in the lower corners. 

3.  Lift the appliance upward, off the mounting posts.

4.  Unplug the appliance.

5.  Unscrew the mounting plate.

6.  Store at -4°F (-20°C) to 158°F (70°C), 5% to 95% humidity

3

 & 

4

Summary of Contents for AirQ AQ1200




























Reviews: