background image

 

Rev 1.4                                                                                                                                     Page 

6 of 14 

 

Standard 

Terminal 

Designations 

Proliphix 

Terminal 

Designations 

Description 

R, RH 

RH 

24VAC for W1 if RC used or all 
HVAC contacts if RC not used 
(see Table 3) 

RC RC 

24VAC for Y1, G if available (see 
Table 3) 

C C 

(not 

used) 

W, W1 

W1 

Heat Relay 

W2 W2 

(Not 

used) 

Y, Y1 

Y1 

Cool Relay 

Y2 Y2 

(Not 

used) 

G G 

Fan 

Relay 

 

- H 

(Not 

used) 

Table 1 Terminal Conversion Chart 

CAT5 Wiring for Ethernet Network 

The inside label on the Base Plate provides several color coded wiring schemes for 
Ethernet CAT5 connections. Match the label number to the Terminal block number for 
CAT5 color coding as shown in Figure 3. If the other end of the CAT5 cable is 
connected to a Proliphix EPA-60 Ethernet Power Adapter, follow the color coding for 
T568A on the label. 

 

Terminal 

block 

number 

CAT5 T568A color code 

White-Blue and Blue ends stripped and 

twisted 

White-Brown and Brown ends stripped and 

twisted 

3 White-Green 
4 Green 
5 White-Orange 
6 Orange 

Table 2 Ethernet  CAT5 Wiring 

 

Summary of Contents for NT20e















Reviews: