PROLiNK PRC3801 User Manual Download

Page: 54 / 92

PROLiNK® PRC3801

Wireless AC1200 MU-MIMO Dual-Band Gigabit Router

Prefix 1 & Prefix 2

•

Enable

: To enable or disable RADVD prefix.

•

Prefix

: Assigned the advertised IPv6 route prefix.

•

AdvOnLinkFlag

: To enable indication that this prefix can be used for on-link determination.

•

AdvAutonomousFlag

: To enable indication that this prefix can be used for autonomous

address configuration.

•

AdvValidLifetime

: Enter the advertises length of time in seconds that the prefix is valid for

purpose of on-link determination.

•

AdvPreferredLifeTime

: Enter the advertises length of time in seconds that addresses generated

from the prefix via stateless address autoconfiguration remain preferred. The special value
infinity means forever

•

AdvRouterAddr

: Enable indication of the address of interface is sent instead of network

prefix.

•

if6to4

: Specifies a logical interface name to derive a 6to4 prefix origin.

Summary of Contents for PRC3801





























































































Search results

Summary of Contents for PRC3801

Reviews:

Related manuals for PRC3801

Brands by name

Popular brands

PROLiNK PRC3801, User Manual

Search results

Summary of Contents for PRC3801

Reviews:

Related manuals for PRC3801

Brands by name

Popular brands