background image

WARRANTY 

The  product  is  covered  by  warranty  under  the  terms  of  the  law  (24  months).  In  case  of 
malfunction  during  the  warranty  period,  the  product  will  be  repaired  or  replaced  at  the 
discretion of the manufacturer. 

The following informations are required for the use of the warranty: 

- Purchase date (the invoice date is valid) 

- Detailed description of the issue. 

It is essential to follow the safety instructions and warnings contained in this manual. 

Any damage caused by non-compliance with the manual causes the warranty to expire. 
The  manufacturer  does  not  take  any  responsibility  for  damages  or  problems  caused  by 
non-compliance with the manual.

 

Any repair that requires the dismantling of the projector assembly screws should only be 
carried  out  by  the  manufacturer,  who  denies  any  responsibility  for  unauthorized 
interventions.  The  dismantling  (even  partial)  of  the  projector  not  carried  out  by  the 
manufacturer causes the warranty to expire. 

The only maintenance operation allowed is the replacement of the lamp. Any other repairs 
must  be  carried  out  solely  by  the  manufacturer,  who  denies  any  responsibility  for 
unauthorized interventions.

The parts of consumption are not covered by the guarantee. 

13

Summary of Contents for IMPRESSIVE EVO 1200

















Reviews: