background image

General Information                                                                                                                                        JB-70 
 

 
 

 
 
 

 

Safety 

Radiation Safety 

Only qualified and authorized personnel may operate this equipment observing 
all laws and regulations concerning radiation protection. 

 

The operator at all times must remain 6ft. (2m) from the focal spot and the X-
ray beam for operator protection. 

 

Full use must be made of all radiation safety features on the equipment. 

 

Full use must be made of all radiation protection devices, accessories and 
procedures available to protect the patient and operator from x-ray radiation.

 

Electrical Safety 

 

Only qualified and authorized service personnel should remove covers on 
the equipment. 

 

This equipment must only be used in rooms or areas that comply with all 
applicable laws and recommendations concerning electrical safety in rooms 
used for medical purposes, e.g., IEC, US National Electrical code, or VDE 
standards concerning provisions of an additional protective earth (ground) 
terminal for power supply connection. 

 

Before cleaning or disinfecting, this equipment must always be disconnected 
from the main electrical supply. 

 

The JB-70 Dental X-Ray System is ordinary type medical equipment without 
protection against ingress of liquids. To protect against short-circuit and 
corrosion, no water or any other liquid should be allowed to leak inside the 
equipment. 

Explosion 
Safety 

This equipment must not be used in the presence of flammable or potentially 
explosive gases or vapors, which could ignite, causing personal injury and/or 
damage to the equipment. If such disinfectants are used, the vapor must be 
allowed to disperse before using the equipment. 

 

Authorized Representatives 

North America 

PROGENY DENTAL 
1407 Barclay Blvd. 
Buffalo Grove, IL 60089 
Phone: 888-924-3800 
Fax: 847-459-5175

 

Europe 

CE Partner 4U 
Nijverheidsstraat 5 
2624 BA Delft 
Netherlands 
Phone: +31-15.2576682 
Fax: +31-15.2576683 

Summary of Contents for I7016






















Reviews: