background image

 

 

IMPORTANT SAFETY INSTRUCTION   

Basic precautions should always be followed, including the following safety 

instructions when using this treadmill: Read all instructions before using this 

treadmill. 

 

DANGER:

 

To reduce the risk of electric shock, please read the following:

 

 

Always unplug the treadmill from the electrical outlet immediately after using 

and before cleaning, assembling, or servicing. 

NOTE: Failure to follow these instructions may lead to personal injury and 

cause damage to the treadmill. 

WARNING:

 

To reduce the risk of burns, fire, electric shock or injury to 

any persons, please read the following: 

 

Never leave the treadmill unattended when plugged in.    Disconnect by   

turning off the master power switch, and unplugging from outlet when not in 

use and before putting on or taking off parts. 

 

Use this appliance only for its intended use as described in this manual.    Do 

not use attachments not recommended by the manufacturer. 

 

Never operate this treadmill if it has a damaged cord or plug, or if it is not 

working properly.    If it has been dropped or damaged, or been exposed to 

water, do not use and consult an 

Authorized Service Representative at 

1-844-641-7920

 

Do not attempt any maintenance or adjustments other than those described in 

this manual.    Should any problems arise, discontinue use and consult an 

Authorized Service Representative.

 

 

Never operate the appliance with the air openings blocked.    Keep the air 

openings free of lint, hair, and the like. 

 

Do not use the treadmill outdoors. 

 

Do not pull the treadmill by its power cord or use the cord as a handle. 

 

Keep children and pets away from the equipment while in use. This machine 

is designed for adults only. This appliance is not intended for use by persons   

with reduced physical, sensory or mental capabilities, or lack of experience and   

knowledge, unless they have been given supervision or instruction concerning   

use of the appliance by a person responsible for their safety. Keep children   

under the age of 13 away from this machine.   

 

IMPORTANT SAFETY INSTRUCTION 

 

Summary of Contents for Walk To Fit




























Reviews: