ProFire SDBOCN, Owner'S Manual, Page: 9 / 20

Assembly Instructions
Back of Grill
4 BOLTS 3/4 "
4 KEP NUTS
BOLT
GRILL
COLUMN
NUT
CONNECTING
GRILL TO COLUMN
CONNECTING
COLUMN TO BASE
6 BOLTS 3/4 "
4 RECTANGULAR
WASHERS
6 1/4 FLAT WASHERS
6 KEP NUTS
INSTALL
BOTH ENDS
NYLON
SPACER
TANK LOCKING BAR
RECT WASHERS
HEAT
SHIELD
IN THIS
ORDER
THIS BASE IS A FIXED (NO WHEELS)
AND MUST BELAGGED TO A DECK OR
CONCRETE FOR STABILITY.
USE THESE 2 HOLES.
BASE
ACCESS FOR GAS
LIN ABOVE DECK
OR PATIO
Step 1A. Follow This Step If You Have Selected
A Stainless Steel Column.
A. In box #2, find and attach the LP Tank Locking Bar
across the back of the column. This spreads and holds
the correct spacing at the back of the column regard-
less of the type of gas that will be used.
( Fig. 1 Page 8)
B.
NOTE: Make sure the protective white film is
peeled away from any area that may not be ac-
cessible after assembly.
Before bolting the stainless steel column to the cast
aluminum base, a 2-piece adhesive gasket must be
installed to make a barrier between the two metals.
Remove the backing strips to expose the adhesive and
stick the gasket to the bottom lip of the stainless steel
column. Align the holes.
( Fig. 2 Page 8)
Attach the column to the base using six 3/4" bolts with
(6) round washers, and on the underside, six round
7/8" dia. washers and six KEP nuts. This assembly is
most easily done with the column lying on its front or
back to provide access to the washers and nuts be-
neath the base. Tighten securely and stand unit up-
right.
PHOENIX
Models: SDSSOPN Nat. Gas
SDSSOPP LP Gas
Stainless Steel Column with
Fixed Base
Ctn. No. FIXED BASE (Propane)
2 1 Stainless Steel Front Panel
3 1 Cast Aluminum Base
2 1 Stainless Column
2 12 1/4-20 Kep Nuts
2 12 1/4
" Washer (7/8" OD)
2 2 Nylon Lock Bar Spacers
2 12 1/4-20 x 3/4 Inch Hex Bolts
2 1 Tank Lock Bar
2 1 2-piece Gasket
Ctn. No. FIXED (Nat. Gas)
2 1 Stainless Steel Front Panel
3 1 Cast Aluminum Base
2 1 Stainless Column
2 12 1/4-20 Kep Nuts
2 12 1/4
" Washer (7/8" OD)
2 2 Nylon Lock Bar Spacers
2 12 1/4-20 x 3/4 Inch Hex Bolts
2 1 Tank Lock Bar
2 1 2-piece Gasket
HARDWARE BY MODEL
Models: SDSSOCN Nat. Gas
SDSSOCP LP Gas
Stainless Steel Column with
Portable Cart Base
Note: Rect.
Washers
Only For
Aluminum
Column
9
Ctn. No. CART (Propane)
2 1 Stainless Steel Front Panel
3 1 Cast Aluminum Base
2 1 Stainless Column
2 12 1/4-20 Kep Nuts
2 12 1/4
" Washer (7/8" OD)
3 2 6 Inch Wheels
3 1 Axle
3 2 Axle Clips
2 2 Nylon Lock Bar Spacers
2 12 1/4-20 x 3/4 Inch Hex Bolts
2 1 Tank Lock Bar
3 2 Hub Caps
2 1 2-piece Gasket
C. On portable bases, attach the wheels by slipping the
axle through the base, slide the wheels on and install
the axle clips. Finish by snapping the hubcaps on before
standing upright. Flat base permanent models must be
Lag Bolted to the deck or concrete for stability.
( Fig. 3
Page 8)
Ctn. No. CART (Nat. Gas)
2 1 Stainless Steel Front Panel
3 1 Cast Aluminum Base
2 1 Stainless Column
2 12 1/4-20 Kep Nuts
2 12 1/4
" Washer (7/8" OD)
3 2 6 Inch Wheels
3 1 Axle
3 2 Axle Clips
2 2 Nylon Lock Bar Spacers
2 12 1/4-20 x 3/4 Inch Hex Bolts
2 1 Tank Lock Bar
3 2 Hub Caps
2 1 2-piece Gasket
3 1 12 Ft. Nat. Gas Hose with
Quick Disconnect