ProFire SDBOCN, Owner'S Manual, Page: 8 / 20

Assembly Instructions
Tools Required For Assembly:
7/16" Wrench, 7/16" Socket Wrench With Extension,
3/8" Wrench.
CAUTION:
Edges of grill may be sharp, use care
when assembling grill.
CAUTION:
While handling the grill head be very care-
ful not to damage the Venturi Tubes or the Ceramic
Ignitor Insulator which protrudes from below the grill.
NOTE: Your Phoenix Grill consists of (3) cartons:
Box 1- Grill Head
Box 2- Black or Stainless Steel Column
Box 3- Cast Aluminum Cart or Flat Base
The column and base should be assembled first, then
the grill head to the completed base assembly.
Assemble As Follows:
Step 1: Follow this step if you have selected the
Black Aluminum Column Mount.
A. In box #2, find and attach the LP Tank Locking Bar
across the back of the column. This spreads and holds
the correct spacing at the back of the column regard-
less of the type of gas that will be used. Use the (2)
3/4" Hex Bolts, Nylon Lock Bar Spacers and Kep Nuts
to fasten the lock bar in place. (
Fig. 1)
B. Align the Holes!
Attach the column to the base using six 3/4 inch bolts,
four large rectangular washers, and on the underside,
six round washers and six Kep nuts. This assembly
work is most easily done with the column lying on its
front or back to provide access to the washers and nuts
beneath the base. (
Fig. 2)
IMPORTANT! The large rectangular washers are used
at the column left and right sides on top of the bottom
lip and under the head of the bolts. The six round
washers are used under the casting. Tighten all se-
curely and stand unit upright.
C. On portable bases, attach the wheels by slipping the
axle through the base, slide the wheels on and install
the axle clips. Finish by snapping the hubcaps on. Flat
base permanent models must be Lag Bolted to the deck
or concrete for stability. (
Fig. 3)
HARDWARE BY MODEL
Ctn. No. CART (Propane)
2 1 Stainless Steel Front Panel
3 1 Cast Aluminum Base
2 1 Aluminum Column
2 12 1/4-20 Kep Nuts
2 6 1/4
" Washer (7/8" OD)
3 2 6 Inch Wheels
3 1 Axle
3 2 Axle Clips
2 2 Nylon Lock Bar Spacers
2 12 1/4-20 x 3/4 Inch Hex Bolts
2 4 Rectangular Washers
2 1 Tank Lock Bar
Ctn. No. CART (Nat. Gas)
2 1 Stainless Steel Front Panel
3 1 Cast Aluminum Base
2 1 Aluminum Column
2 12 1/4-20 Kep Nuts
2 6 1/4
" Washer (7/8" OD)
3 2 6 Inch Wheels
3 1 Axle
3 2 Axle Clips
2 2 Nylon Lock Bar Spacers
2 12 1/4-20 x 3/4 Inch Hex Bolts
2 4 Rectangular Washers
2 1 Tank Lock Bar
3 2 Hub Caps
Models: SDBOPN Nat. Gas
SDBOPP LP Gas
Black Column with Fixed Base
Models: SDBOCN Nat. Gas
SDBOCP LP Gas
Black Column with Portable Cart Base
Ctn. No. FIXED BASE (Propane)
2 1 Stainless Steel Front Panel
3 1 Cast Aluminum Base
2 1 Aluminum Column
2 12 1/4-20 Kep Nuts
2 6 1/4
" Washer (7/8" OD)
2 2 Nylon Lock Bar Spacers
2 12 1/4-20 x 3/4 Inch Hex Bolts
2 4 Rectangular Washers
2 1 Tank Lock Bar
Ctn. No. FIXED BASE (Nat. Gas)
2 1 Stainless Steel Front Panel
3 1 Cast Aluminum Base
2 1 Aluminum Column
2 12 1/4-20 Kep Nuts
2 6 1/4
" Washer (7/8" OD)
2 2 Nylon Lock Bar Spacers
2 12 1/4-20 x 3/4 Inch Hex Bolts
2 4 Rectangular Washers
2 1 Tank Lock Bar
Go To Step 1A If You Have A Stainless Steel Column
Tank
Locking Bar
Nylon
Spacer
Kep
Nut
Hex
Bolt
Fig. 1 Fig. 3
Axle, Wheel, Clip Pin and
Hub Cap
Rec. Washers
Only For Aluminum
Column
2-Piece Gasket
For Stainless
Column Only
Fig. 2
Attach in this order– Bolt, Rec. Washer,
Washer, Kep Nut
8